- 您現在的位置：買賣IC網 > PDF目錄363744 > OM5284EP02 (NXP Semiconductors N.V.) CMOS single-chip 8-bit microcontrollers PDF資料下載
參數資料
| 型號： | OM5284EP02 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | CMOS single-chip 8-bit microcontrollers |
| 中文描述： | CMOS單芯片8位微控制器 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 106K |
| 代理商： | OM5284EP02 |
Philips Semiconductors
Preliminary specification
OM5234/OM5284
CMOS single-chip 8-bit microcontrollers
1996 Nov 01
4
PIN DESCRIPTIONS
PIN NUMBER
MNEMONIC PLCC
QFP
DIP
TYPE
NAME AND FUNCTION
V
SS
22
6, 16,
28, 39
20
I
Ground:
0V reference. With the QFP package, all V
SS
pins (V
SS1
to V
SS4
) must be
connected.
V
DD
44
38
40
I
Power Supply:
This is the power supply voltage for normal, idle, and power-down
operation.
P0.0–0.7
43–36
37–30
39–32
I/O
Port 0:
Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to
them float and can be used as high-impedance inputs. Port 0 is also the multiplexed
low-order address and data bus during accesses to external program and data memory.
In this application, it uses strong internal pull-ups when emitting 1s.
P1.0–P1.7
2–9
40–44,
1–3
1–8
I/O
Port 1:
Port 1 is an 8-bit bidirectional I/O port with internal pull-ups, except P1.6 and P1.7,
which are open drain for OM5234 (only). Port 1 pins that have 1s written to them are
pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins that
are externally pulled low will source current because of the internal pull-ups. (See DC
Electrical Characteristics: I
IL
). Alternate functions include:
Bidirectional I/O with internal pull-ups (OM5284), and open drain for (OM5234).
Bidirectional I/O with internal pull-ups (OM5284), and open drain for (OM5234).
P1.6
P1.7
8
9
2
3
7
8
I/O
I/O
P2.0–P2.7
24–31
18–25
21–28
I/O
Port 2:
Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have
1s written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 2 pins that are externally being pulled low will source current because of the
internal pull-ups. (See DC Electrical Characteristics: I
). Port 2 emits the high-order
address byte during fetches from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it
uses strong internal pull-ups when emitting 1s. During accesses to external data memory
that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function
register.
P3.0–P3.7
11,
13–19
5,
7–13
10–17
I/O
Port 3:
Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have
1s written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 3 pins that are externally being pulled low will source current because of the
pull-ups. (See DC Electrical Characteristics: I
IL
). Port 3 also serves the special features of
the 80C51 family, as listed below:
RxD (P3.0):
Serial input port
TxD (P3.1):
Serial output port
INT0 (P3.2):
External interrupt
INT1 (P3.3):
External interrupt
T0 (P3.4):
Timer 0 external input
T1 (P3.5):
Timer 1 external input
WR (P3.6):
External data memory write strobe
RD (P3.7):
External data memory read strobe
11
13
14
15
16
17
18
19
5
7
8
9
10
11
12
13
10
11
12
13
14
15
16
17
I
O
I
I
I
I
O
O
RST
10
4
9
I
Reset:
A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V
SS
permits a power-on reset using only an
external capacitor to V
CC
.
Address Latch Enable:
Output pulse for latching the low byte of the address during an
access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6
the oscillator frequency. Note that one ALE pulse is skipped during each access to
external data memory.
ALE
33
27
30
I/O
PSEN
32
26
29
O
Program Store Enable:
Read strobe to external program memory via Port 0 and Port 2.
It is activated twice each machine cycle during fetches from the external program
memory. When executing out of external program memory, two activations of PSEN are
skipped during each access to external data memory. PSEN is not activated (remains
HIGH) during fetches from external program memory. PSEN can sink/source 8 LSTTL
inputs and can drive CMOS inputs without external pull-ups.
EA
35
29
31
I
External Access:
If during a RESET, EA is held at TTL, level HIGH, the CPU executes
out of the internal program memory ROM provided the Program Counter is less than
16384. If during a RESET, EA is held at TTL LOW level, the CPU executes out of external
program memory. EA is not allowed to float.
XTAL1
21
15
19
I
Crystal 1:
Input to the inverting oscillator amplifier and input to the internal clock
generator circuits.
XTAL2
NOTE:
To avoid “l(fā)atch-up” effect at power-on, the voltage on any pin at any time must not be higher than V
DD
+ 0.5V or V
SS
– 0.5V, respectively.
20
14
18
O
Crystal 2:
Output from the inverting oscillator amplifier.
相關PDF資料 |
PDF描述 |
|---|---|
| OM5284EP03 | CMOS single-chip 8-bit microcontrollers |
| OM5284EB01 | CMOS single-chip 8-bit microcontrollers |
| OM5284IA01 | CMOS single-chip 8-bit microcontrollers |
| OM5284IA02 | CMOS single-chip 8-bit microcontrollers |
| OM5284IA03 | CMOS single-chip 8-bit microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OM5284EP03 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| OM5284EPYY | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| OM5284IA01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| OM5284IA02 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
| OM5284IA03 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。