- 您現在的位置：買賣IC網 > PDF目錄363670 > NT7501 (Electronic Theatre Controls, Inc.) 33 X 100 RAM-Map LCD Controller/Driver PDF資料下載
參數資料
| 型號： | NT7501 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 33 X 100 RAM-Map LCD Controller/Driver |
| 中文描述： | 33 × 100 RAM的地圖LCD控制器/驅動器 |
| 文件頁數： | 18/38頁 |
| 文件大小： | 319K |
| 代理商： | NT7501 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
NT7501
18
COMMANDS
The NT7501 uses a combination of A0, RD(E) and WR (
executes each command using the internal timing clock only, (regardless of external clock) its processing speed is very high
and its busy check is usually not required. The 8080 series microprocessor interface enters read status when a low pulse is
input to the RD pad and write status when a low pulse is input to the WR pad. The 6800 series microprocessor interface enters
read status when a high pulse is input to the
W
R
pad and write status when a low pulse is input to this pad. When a high pulse
is input to the E pad, the command is activated. (For timing, see AC Characteristics.). Accordingly, in the command explanation
and command table, RD (E) becomes 1(high) when the 6800 series microprocessor interface reads the status of display data.
This is an only different point from the 8080 series microprocessor interface.
Looking at the 8080 series, microprocessor interface example commands are explained below.
When the serial interface is selected, input data in sequence starting from D7.
W
R
) signals to identify data bus signals. As the chip analyzes and
Command Set
1. Display ON/OFF
Alternatively turns the display on and off.
A0
E
RD
W
R
WR
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
1
0
1
0
1
1
1
D
The display turns off when D goes low and it turns on when D goes high.
2. Set Display Start Line
Specifies the line address (refer to Figure 4) to determine the initial display line, or COM0. The RAM display data becomes
the top line of the LCD screen. It is followed by the higher number of lines in ascending order, corresponding to the duty
cycle. When this command changes the line address, the smooth scrolling or page change takes place.
A0
E
RD
W
R
WR
0
D7
D6
D5
D4
D3
D2
D1
D0
0
1
0
1
A5
A4
A3
A2
A1
A0
A5
A4
A3
A2
A1
A0
Line address
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
1
0
2
:
:
1
1
1
1
1
0
62
1
1
1
1
1
1
63
相關PDF資料 |
PDF描述 |
|---|---|
| NT7501H-BDT | 33 X 100 RAM-Map LCD Controller/Driver |
| NT7502 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 65 X 132 RAM-Map LCD Controller / Driver |
| NT7603 | 2 x 110 W class-D power amplifer, SOT566-3 (HSOP24), Reel Pack, SMD, 13" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT7501H-BDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:33 X 100 RAM-Map LCD Controller/Driver |
| NT7502 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-BDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT7502H-TABF1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:65 X 132 RAM-Map LCD Controller / Driver |
| NT75-1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Low coil consumption. / Switching capacity up to 16A. |
發布緊急采購，3分鐘左右您將得到回復。