- 您現在的位置：買賣IC網 > PDF目錄363668 > NSSM016AT (Electronic Theatre Controls, Inc.) NICHIA CHIP TYPE FULL COLOR LED PDF資料下載
參數資料
| 型號： | NSSM016AT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | NICHIA CHIP TYPE FULL COLOR LED |
| 中文描述： | 日亞片式全彩LED |
| 文件頁數： | 6/13頁 |
| 文件大小： | 288K |
| 代理商： | NSSM016AT |
-5-
120sec.Max.
Pre-heating
180 ~ 200°C
260°C
Max.
10sec. Max.
60sec.Max.
Above 220°C
1 ~ 5°C / sec.
1 ~ 5°C / sec.
<
1
: Lead Solder>
<
2
: Lead-free Solder>
Pre-heating
120 ~ 150°C
240°C
Max.
10sec. Max.
60sec.Max.
Above 200
°C
2.5 ~ 5°C / sec.
2.5 ~ 5°C / sec.
[Recommended soldering pad design] Use the following conditions shown in the figure.
2.75
3
3
120sec.Max.
Nichia STSE-CM4025A
<Cat.No.040701>
(4) Soldering Conditions
· The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a
guarantee on the LEDs after they have been assembled using the dip soldering method.
· Recommended soldering conditions
Reflow Soldering
Lead Solder
Lead-free Solder
Pre-heat
Pre-heat time
Peak
temperature
Soldering time
Condition
Temperature - profile
1
.
(N
2
reflow is recommended.)
!
After reflow soldering rapid cooling should be avoided.
[Temperature-profile
(Surface of circuit board)
] Use the conditions shown to the under figure.
Hand Soldering
120
~
150°C
120 sec. Max.
240°C Max.
10 sec. Max.
refer to
180
~
200°C
120 sec. Max.
260°C Max.
10 sec. Max.
refer to
Temperature - profile
2
.
Temperature
Soldering time
350°C Max.
3 sec. Max.
(one time only)
· Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere
during air reflow. It is recommended that the User use the nitrogen reflow method.
· Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used. It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.
· Reflow soldering should not be done more than two times.
·
When soldering, do not put stress on the LEDs during heating.
·
After soldering, do not warp the circuit board.
(5) Cleaning
· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using
other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the
resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations.
· Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic
cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.
Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.
(Unit : mm)
8.75
1
1
1
5
相關PDF資料 |
PDF描述 |
|---|---|
| NSSW020AT | SPECIFICATION FOR NICHIA CHIP TYPE WHITE LED |
| NST3904DXV6T5 | Dual General Purpose Transistor |
| NST3904DXV6T1 | LCD Displays 10.4 inch (26.0 cm) 18-bit digital (6 bits/color) |
| NSTB60BDW1T1 | PNP General Purpose and NPN Bias Resistor Transistor Combination(PNP通用與NPN偏置電阻晶體管組合) |
| NSTM515AS | SPECIFICATIONS FOR NICHIA FULL COLOR LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NSSM016C | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:SPECIFICATIONS FOR NICHIA CHIP TYPE FULL COLOR LED |
| NSSM016CT | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:SPECIFICATIONS FOR NICHIA CHIP TYPE FULL COLOR LED |
| NSSM016D | 制造商:Nichia CORPORATION 功能描述:LED, SMD,Display,B400,G1600,R700mcd |
| NSSM016DT | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:TYPE FULL COLOR LED |
| NSSM016XT | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:SPECIFICATIONS FOR NICHIA CHIP TYPE FULL COLOR LED |
發布緊急采購，3分鐘左右您將得到回復。