- 您現在的位置：買賣IC網 > PDF目錄361106 > ND12S0A0V50PNFA (Delta Electronics, Inc.) Delphi ND Series Non-Isolated Point of Load DC/DC Power Modules: 12Vin, 0.9V~3.63Vout, 50Aout PDF資料下載
參數資料
| 型號： | ND12S0A0V50PNFA |
| 廠商： | Delta Electronics, Inc. |
| 英文描述： | Delphi ND Series Non-Isolated Point of Load DC/DC Power Modules: 12Vin, 0.9V~3.63Vout, 50Aout |
| 中文描述： | 德爾福釹系列非隔離負載點DC / DC電源模塊：12Vin，0.9?3.63Vout，50Aout |
| 文件頁數： | 7/12頁 |
| 文件大小： | 515K |
| 代理商： | ND12S0A0V50PNFA |
DS_ND12S10A_03082007
7
DESIGN CONSIDERATIONS
The ND 50A uses two phase and voltage mode controlled
buck topology. The output can be trimmed in the range of
0.9Vdc to 3.63Vdc with a resistor from Trim pin to Ground.
A remote sense function is provided and it is able to
compensate for a drop from the output of converter to
point of load.
The converter can be turned ON/OFF by remote control.
Positive on/off (ENABLE pin) logic implies that the
converter DC output is enabled when
the signal is driven
high (greater than 2.4V) or floating and disabled when the
signal is driven low (below 0.8V). Negative on/off logic is
optional.
The converter provides an open collector Power Good
signal. The power good signal is pulled low when output is
not within ±10% of Vout or Enable is OFF.
The converter can protect itself by entering hiccup mode
against over current and short circuit condition.
The converter has an over temperature protection which
can protect itself by shutting down for an over
temperature event. There is a thermal hysteresis of
typically 20°C
Safety Considerations
It is recommended that the user to provide a very
fast-acting type fuse in the input line for safety. The output
voltage set-point and the output current in the application
could define the amperage rating of the fuse.
FEATURES DESCRIPTIONS
ENABLE (On/Off)
The ENABLE (on/off) input allows external circuitry to put
the ND converter into a low power dissipation (sleep)
mode. Positive ENABLE is available as standard.
Positive ENABLE units of the ND series are turned on if
the ENABLE pin is high or floating. Pulling the pin low will
turn off the unit. With the active high function, the output is
guaranteed to turn on if the ENABLE pin is driven above
2.4V. The output will turn off if the ENABLE pin voltage is
pulled below 0.8V.
The ENABLE input can be driven in a variety of ways as
shown in Figures 23 and 24. If the ENABLE signal comes
from the primary side of the circuit, the ENABLE can be
driven through either a bipolar signal transistor (Figure
23). If the enable signal comes from the secondary side,
then an opto-coupler or other isolation devices must be
used to bring the signal across the voltage isolation
(please see Figure 24).
Figure 23:
Enable Input drive circuit for ND series
Figure 24
: Enable input drive circuit example with isolation.
相關PDF資料 |
PDF描述 |
|---|---|
| ND2012L | N-Channel Depletion-Mode MOSFET Transistors(最大漏源導通電阻12Ω，夾斷電流0.16A的N溝道耗盡型MOSFET晶體管) |
| ND2020L | N-Channel Depletion-Mode MOSFET Transistors(最大漏源導通電阻20Ω，夾斷電流0.132A的N溝道耗盡型MOSFET晶體管) |
| ND3000 | S TO K-BAND GaAs VARACTOR DIODE |
| ND3050A | S TO K-BAND GaAs VARACTOR DIODE |
| ND3050B | S TO K-BAND GaAs VARACTOR DIODE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ND130A | 制造商:BRITOOL 功能描述:COMBINATION SPANNER SET 1/8-1/2 WH |
| ND14 | 制造商:Cooper Hand Tools / Xcelite 功能描述: |
| ND1414 | 制造商:OHIO BUCKEYE 功能描述: |
| ND14141.006156 | 制造商:PEAK_INC 制造商全稱:PEAK_INC 功能描述:ND14141.006156 REV.A |
| ND14141.006158 | 制造商:PEAK_INC 制造商全稱:PEAK_INC 功能描述:ND14141.006158 REV.A |
發布緊急采購，3分鐘左右您將得到回復。