- 您現在的位置：買賣IC網 > PDF目錄363234 > NCV4299 (ON SEMICONDUCTOR) 5.0V Low Drop Fixed Voltage Regulator(5.0V，低壓差固定電壓穩壓器) PDF資料下載
參數資料
| 型號： | NCV4299 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | 5.0V Low Drop Fixed Voltage Regulator(5.0V，低壓差固定電壓穩壓器) |
| 中文描述： | 固定5.0V低壓差穩壓器（5.0V，低壓差固定電壓穩壓器） |
| 文件頁數： | 17/23頁 |
| 文件大小： | 197K |
| 代理商： | NCV4299 |
NCV4299
http://onsemi.com
17
Setting the Delay Time
The delay time is set by the delay capacitor C
D
and the
charge current I
D
. The time is measured by the delay
capacitor voltage charging from the low level of V
D,sat
to the
higher level V
UD
. The time delay follows the equation:
td
[CD(VUD-VD,sat)] ID
(eq. 2)
Example:
Using C
D
= 100 nF.
Use the typical value for V
D,sat
= 0.1 V.
Use the typical value for V
UD
= 1.8 V.
Use the typical value for Delay Charge Current I
D
= 6.5 A.
td
[100nF(1.8-0.1V)]
6.5 A
26.2ms
(eq. 3)
When the output voltage V
Q
drops below the reset
threshold voltage V
RT
, the voltage on the delay capacitor V
D
starts to drop. The time it takes to drop below the lower
threshold voltage of V
LD
is the reset reaction time, t
RR
. This
time is typically 2.2 s for a delay capacitor of 0.1 F. The
reset reaction time can be estimated from the following
relationship:
tRR
22ns nF
CD
(eq. 4)
Sense Input (SI)/Sense Output (SO) Voltage Monitor
An on-chip comparator is available to provide early
warning to the microprocessor of a possible reset signal. The
reset signal typically turns the microprocessor off
instantaneously. This can cause unpredictable results with
the microprocessor. The signal received from the SO pin will
allow the microprocessor time to complete its present task
before shutting down. This function is performed by a
comparator referenced to the band gap voltage. The actual
trip point can be programmed externally using a resistor
divider to the input monitor (SI) (Figures 39 and 40). The
typical threshold is 1.35 V on the SI Pin.
Signal Output
Figure 42 shows the SO Monitor waveforms as a result of
the circuits depicted in Figures 39 and 40. As the output
voltage V
Q
falls, the monitor threshold V
SI,LOW
is crossed.
This causes the voltage on the SO output to go low sending
a warning signal to the microprocessor that a reset signal may
occur in a short period of time. T
WARNING
is the time the
microprocessor has to complete the function it is currently
working on and get ready for the reset shutdown signal.
t
PD SO LH
t
PD SO HL
t
t
Sense
Input
Voltage
V
SL, High
V
SL, Low
Sense
Output
High
Low
V
Q
S
I
V
SI,LOW
V
RO
S
O
T
WARNING
Figure 42. SO Warning Timing Waveform
Figure 43. Sense Timing Diagram
Calculating Power Dissipation in a Single Output
Linear Regulator
The maximum power dissipation for a single output
regulator is:
PD(max)
[VI(max)-VQ(min)]IQ(max)
VI(max)Iq
(eq. 5)
where:
V
I(max)
is the maximum input voltage,
V
Q(min)
is the minimum output voltage,
I
Q(max)
is the maximum output current for the application,
and
I
q
is the quiescent current the regulator consumes at I
Q(max)
.
Once the value of P
D(max)
is known, the maximum
permissible value of R
JA
can be calculated:
RJA
(150
°
C-TA) PD
(eq. 6)
The value of R
JA
can then be compared with those in the
package section of the data sheet. Those packages with
R
JA
's less than the calculated value in Equation 6 will keep
the die temperature below 150
°
C. In some cases, none of the
packages will be sufficient to dissipate the heat generated by
the IC, and an external heatsink will be required.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV431A | Programmable Precision References(可編程精密基準) |
| NCV7356 | Single Wire CAN Transceiver(單線CAN收發器) |
| NCV7361A | Voltage Regulator with Integrated LIN Transceiver(帶有集成LIN收發器的穩壓器) |
| NCV7361 | Voltage Regulator with Integrated LIN Transceiver |
| NCV7361AD | Voltage Regulator with Integrated LIN Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV4299AD233R2G | 功能描述:IC REG LDO 3.3V .15A 20SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:2,000 系列:- 穩壓器拓撲結構:正，可調式 輸出電壓:1.2 V ~ 5 V 輸入電壓:2.5 V ~ 7 V 電壓 - 壓降（標準）:0.24V @ 800mA 穩壓器數量:1 電流 - 輸出:800mA 電流 - 限制（最?。?1.2A 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-261-5，TO-261AB 供應商設備封裝:SOT-223-5 包裝:帶卷 (TR) 其它名稱:*LP3964EMPX-ADJLP3964EMPX-ADJLP3964EMPX-ADJ-NDLP3964EMPX-ADJ/NOPBTR |
| NCV4299AD250R2G | 功能描述:低壓差穩壓器 - LDO 150 MA LOW IQ LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCV4299D1 | 功能描述:低壓差穩壓器 - LDO 5V 400mA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCV4299D1G | 功能描述:低壓差穩壓器 - LDO LDO REG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCV4299D1R2 | 功能描述:低壓差穩壓器 - LDO 5V 400mA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。