- 您現在的位置：買賣IC網 > PDF目錄363233 > NCV2574 (ON SEMICONDUCTOR) 0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator(0.5A,可調輸出電壓,降壓型開關穩壓器) PDF資料下載
參數資料
| 型號： | NCV2574 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | 0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator(0.5A,可調輸出電壓,降壓型開關穩壓器) |
| 中文描述： | 0.5甲，可調輸出電壓，降壓型開關穩壓器（0.5A的，可調輸出電壓，降壓型開關穩壓器） |
| 文件頁數： | 10/26頁 |
| 文件大?。?/td> | 295K |
| 代理商： | NCV2574 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LM2574, NCV2574
http://onsemi.com
10
Procedure
(Fixed Output Voltage Version)
In order to simplify the switching regulator design, a stepbystep design
procedure and example is provided.
Procedure
Example
Given Parameters:
V
out
= Regulated Output Voltage (3.3 V, 5.0 V, 12 V or 15 V)
V
in(max)
= Maximum Input Voltage
I
Load(max)
= Maximum Load Current
Given Parameters:
V
out
= 5.0 V
V
in(max)
= 15 V
I
Load(max)
= 0.4 A
1. Controller IC Selection
According to the required input voltage, output voltage and
current, select the appropriate type of the controller IC output
voltage version.
1. Controller IC Selection
According to the required input voltage, output voltage,
current polarity and current value, use the LM25745
controller IC.
2. Input Capacitor Selection (C
in
)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +V
in
and ground pin Gnd. This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
2. Input Capacitor Selection (C
in
)
A 22 F, 25 V aluminium electrolytic capacitor located near
to the input and ground pins provides sufficient bypassing.
3. Catch Diode Selection (D1)
A.
Since the diode maximum peak current exceeds the
regulator maximum load current, the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design the diode should have a
current rating equal to the maximum current limit of the
LM2574 to be able to withstand a continuous output short.
B.
The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A
.For this example the current rating of the diode is 1.0 A.
B.
Use a 20 V 1N5817 Schottky diode, or any of the
suggested fast recovery diodes shown in Table 1.
4. Inductor Selection (L1)
A.
According to the required working conditions, select the
correct inductor value using the selection guide from
Figures 19 to 23.
B.
From the appropriate inductor selection guide, identify the
inductance region intersected by the Maximum Input Voltage
line and the Maximum Load Current line. Each region is
identified by an inductance value and an inductor code.
C.
Select an appropriate inductor from the several different
manufacturers part numbers listed in
Table 2. The designer
must realize that the inductor current rating must be higher
than the maximum peak current flowing through the inductor.
This maximum peak current can be calculated as follows:
where t
on
is the “on” time of the power switch and
V
out
For additional information about the inductor, see the inductor
section in the “EXTERNAL COMPONENTS” section of this
data sheet.
I
p
(
max
)
I
Load
(
max
)
V
in
V
out
t
on
2L
t
on
V
in
x1.0
f
osc
4. Inductor Selection (L1)
A.
Use the inductor selection guide shown in Figure 20.
B.
From the selection guide, the inductance area
intersected by the 15 V line and 0.4 A line is 330.
C.
Inductor value required is 330 H. From Table 2, choose
an inductor from any of the listed manufacturers.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV2904DR2 | DUAL DIFFERENTIAL INPUT OPERATIONAL AMPLIFIERS |
| NCV2931 | 100 mA, Adjustable Output, LDO Voltage Regulator with 60 V Load Dump Protection(100mA，可調輸出，帶有60V負載保護的低壓差穩壓器) |
| NCV2951 | 100 mA, Low Power Low Dropout Voltage Regulator(100mA，低功耗低壓差穩壓器) |
| NCV33033 | Brushless DC Motor Controller(無刷直流電機控制器) |
| NCV33035 | Brushless DC Motor Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV2574DW-ADJR2 | 功能描述:直流/直流開關調節器 ASECLSW REG RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| NCV2574DW-ADJR2G | 功能描述:直流/直流開關調節器 ASECLSW REG RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| NCV2574DW-ADJR2G | 制造商:ON Semiconductor 功能描述:Switching Regulator |
| NCV2575 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator |
| NCV2575D2T-12G | 功能描述:直流/直流開關調節器 ANA 12V 1A PW SW REG RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。