- 您現在的位置：買賣IC網 > PDF目錄361100 > NCP348MTTXG (ON SEMICONDUCTOR) Positive Overvoltage Protection Controller with Internal Low R_ON NMOS FET and Status FLAG PDF資料下載
參數資料
| 型號： | NCP348MTTXG |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | MOSFETs |
| 英文描述： | Positive Overvoltage Protection Controller with Internal Low R_ON NMOS FET and Status FLAG |
| 中文描述： | HALF BRDG BASED MOSFET DRIVER, DSO10 |
| 封裝： | 2.50 X 2 MM, 0.50 MM PITCH, LEAD FREE, WDFN-10 |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 285K |
| 代理商： | NCP348MTTXG |
NCP348
http://onsemi.com
3
PIN FUNCTION DESCRIPTION
Pin No.
Symbol
Function
Description
1
4
5
IN
POWER
Input Voltage Pin.
This pin is connected to the power supply.
The device system core is supplied by this input.
A 1 F low ESR ceramic capacitor, or larger, must be connected between this pin and GND.
The three IN pins must be hardwired to common supply.
2
GND
POWER
Ground
3
FLAG
OUTPUT
Fault Indication Pin.
This pin allows an external system to detect a fault on IN pin.
The FLAG pin goes low when input voltage exceeds OVLO threshold or drop below UVLO threshold.
Since the FLAG pin is open drain functionality, an external pull up resistor to V
CC
must be added.
6
7
OUT
OUTPUT
Output Voltage Pin.
This pin follows IN pin when “no fault” is detected.
The output is disconnected from the V
in
power supply when the input voltage is under the UVLO
threshold or above OVLO threshold.
The two OUT pins must be hardwired to common supply.
8
NC
OPEN
No Connect
9
NC
OPEN
No Connect
10
EN
INPUT
Enable Pin.
The device enters in shutdown mode when this pin is tied to a high level. In this case the output is
disconnected from the input.
To allow normal functionality, the EN pin shall be connected to GND to a pull down or to a I/O pin.
This pin does not have an impact on the fault detection.
PAD1
PAD1, under the device. See PCB recommendations page 10.
Can be shorted to GND.
PAD2
The PAD2 is electrically connected to the internal NMOS drain and connected to Pins 4 and 5.
See PCB recommendations page 10.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Minimum Voltage (IN to GND)
Vmin
in
0.3
V
Minimum Voltage (All others to GND)
Vmin
0.3
V
Maximum Voltage (IN to GND)
Vmax
in
30
V
Maximum Voltage (All others to GND)
Vmax
7.0
V
Maximum Current (UVLO<V
IN
<OVLO)
Imax
2.0
A
Thermal Resistance, JunctiontoAir (Note 1)
R
JA
280
°
C/W
Operating Ambient Temperature Range
T
A
40 to +85
°
C
Storage Temperature Range
T
stg
65 to +150
°
C
Junction Operating Temperature
T
J
150
°
C
ESD Withstand Voltage (IEC 6100042) (input only) when bypassed with 1.0 F capacitor
Human Body Model (HBM), Model = 2 (Note 2)
Machine Model (MM) Model = B (Note 3)
Vesd
15 Air, 8.0 Contact
2000
200
kV
V
V
Moisture Sensitivity
MSL
Level 1
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The R
is highly dependent on the PCB heat sink area (connected to pad 2). As example R
JA
is 268
°
C/W with 30 mm
2
(copper 35 m) and
189
°
C/W with 400 mm
2
.
2. Human Body Model, 100 pF discharged through a 1.5 k resistor following specification JESD22/A114.
3. Machine Model, 200 pF discharged through all pins following specification JESD22/A115.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP400 | 150 mA CMOS Low Iq Low-Dropout Voltage Regulator with Voltage Detector Output |
| NCP400FCT2G | 150 mA CMOS Low Iq Low-Dropout Voltage Regulator with Voltage Detector Output |
| NCP4326DR2 | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| NCP4326DR2G | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
| NCP4330DR2G | Post Regulation Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP349 BB58C WAF | 制造商:ON Semiconductor 功能描述: |
| NCP349GEVB | 功能描述:電源管理IC開發工具 POSITIVE OVP EVB RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP349MNAETBG | 功能描述:電壓監測器/監控器 POSITIVE OVP RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| NCP349MNBGTBG | 功能描述:電壓監測器/監控器 POSITIVE OVP RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| NCP349MNBKTBG | 功能描述:電壓監測器/監控器 POSITIVE OVP RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。