- 您現在的位置：買賣IC網 > PDF目錄361099 > NCP3488DR2G (ON SEMICONDUCTOR) MOSFET Driver with Dual Outputs for Synchronous Buck Converters PDF資料下載
參數資料
| 型號： | NCP3488DR2G |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | MOSFETs |
| 英文描述： | MOSFET Driver with Dual Outputs for Synchronous Buck Converters |
| 中文描述： | HALF BRDG BASED MOSFET DRIVER, PDSO8 |
| 封裝： | LEAD FREE, SOP-8 |
| 文件頁數： | 6/7頁 |
| 文件大小： | 144K |
| 代理商： | NCP3488DR2G |
NCP3488
http://onsemi.com
6
Safety Timer and Overlap Protection Circuit
It is very important that MOSFETs in a synchronous buck
regulator do not both conduct at the same time. Excessive
shoot
through or cross conduction can damage the
MOSFETs, and even a small amount of cross conduction
will cause a decrease in the power conversion efficiency.
The NCP3488 prevents cross conduction by monitoring
the status of the external MOSFETs and applying the
appropriate amount of “dead
time” or the time between the
turn off of one MOSFET and the turn on of the other
MOSFET.
When the PWM input pin goes high, DRVL will go low
after a propagation delay (tpdlDRVL). The time it takes for
the low
side MOSFET to turn off (tfDRVL) is dependent on
the total charge on the low
side MOSFET gate. The
NCP3488 monitors the gate voltage of both MOSFETs and
the switchnode voltage to determine the conduction status of
the MOSFETs. Once the low
side MOSFET is turned off an
internal timer will delay (tpdhDRVH) the turn on of the
high
side MOSFET
Likewise, when the PWM input pin goes low, DRVH will
go low after the propagation delay (tpdDRVH). The time to
turn off the high
side MOSFET (tfDRVH) is dependent on
the total gate charge of the high
side MOSFET. A timer will
be triggered once the high
side MOSFET has stopped
conducting, to delay (tpdhDRVL) the turn on of the
low
side MOSFET
Power Supply Decoupling
The NCP3488 can source and sink relatively large
currents to the gate pins of the external MOSFETs. In order
to maintain a constant and stable supply voltage (V
CC
) a low
ESR capacitor should be placed near the power and ground
pins. A 1 F to 4.7 F multi layer ceramic capacitor (MLCC)
is usually sufficient.
Input Pins
The PWM input and the Output Disable pins of the
NCP3488 have internal protection for Electro Static
Discharge (ESD), but in normal operation they present a
relatively high input impedance. If the PWM controller does
not have internal pull
down resistors, they should be added
externally to ensure that the driver outputs do not go high
before the controller has reached its under voltage lockout
threshold. The NCP5388 controller does include a passive
internal pull
down resistor on the drive
on output pin.
Bootstrap Circuit
The bootstrap circuit uses a charge storage capacitor
(C
BST
) and the internal (or an external) diode. Selection of
these components can be done after the high
side MOSFET
has been chosen. The bootstrap capacitor must have a
voltage rating that is able to withstand twice the maximum
supply voltage. A minimum 50 V rating is recommended.
The capacitance is determined using the following equation:
CBST
QGATE
VBST
where Q
GATE
is the total gate charge of the high
side
MOSFET, and V
BST
is the voltage droop allowed on the
high
side MOSFET drive. For example, a NTD60N03 has
a total gate charge of about 30 nC. For an allowed droop of
300 mV, the required bootstrap capacitance is 100 nF. A
good quality ceramic capacitor should be used.
The bootstrap diode must be rated to withstand the
maximum supply voltage plus any peak ringing voltages
that may be present on SW. The average forward current can
be estimated by:
IF(AVG)
QGATE
fMAX
where f
MAX
is the maximum switching frequency of the
controller. The peak surge current rating should be checked
in
circuit, since this is dependent on the source impedance
of the 12 V supply and the ESR of CBST.
NCP3488
4
3
2
5
6
7
8
1
Vcc
OD
IN
DSW
PGND
DRVH
BST
Vout
12 V
Output Enable
12 V
PWM in
Figure 4. NCP3488 Example Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| NCP348MTTBG | Positive Overvoltage Protection Controller with Internal Low R_ON NMOS FET and Status FLAG |
| NCP348MTTXG | Positive Overvoltage Protection Controller with Internal Low R_ON NMOS FET and Status FLAG |
| NCP400 | 150 mA CMOS Low Iq Low-Dropout Voltage Regulator with Voltage Detector Output |
| NCP400FCT2G | 150 mA CMOS Low Iq Low-Dropout Voltage Regulator with Voltage Detector Output |
| NCP4326DR2 | Secondary Controller for Multi−Output Quasi−Resonant Switchmode Power Supplies |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP348AEMTTBG | 功能描述:監控電路 POS OVERVLTG PROTECT CONTROLLER RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP348AEMTTBG-CUT TAPE | 制造商:ON 功能描述:NCP348AE Series 6.4 V Threshold 28 V Positive Overvoltage Protection Controller |
| NCP348AEMTTXG | 功能描述:監控電路 POS OVERVLTG PROTECT CONTROLLER RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP348AEMUTBG | 功能描述:監控電路 POSTIVE OVP PRTCTION RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP348GEVB | 功能描述:電源管理IC開發工具 EVALUATION BRD DEV RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。