- 您現在的位置：買賣IC網 > PDF目錄361099 > NCP1651 (ON SEMICONDUCTOR) Single Stage Power Factor Controller PDF資料下載
參數資料
| 型號： | NCP1651 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Single Stage Power Factor Controller |
| 中文描述： | 單級功率因數控制器 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 57K |
| 代理商： | NCP1651 |
NCP345
http://onsemi.com
6
Normal Operation
Figure 1 illustrates a typical configuration. The external
adapter provides power to the protection system so the
circuitry is only active when the adapter is connected. The
OVP monitors the voltage from the charger and if the
voltage exceeds a nominal voltage of 6.85 V, the OUT signal
drives the gate of the MOSFET to within 1.0 V of V
CC
, thus
turning off the FET and disconnecting the source from the
load. The nominal time it takes to drive the gate to this state
is 400 nsec (1.0 usec maximum for gate capacitance of
< 12 nF). Typical turn off performance using the CNTRL
input can be seen in Figure 6. The CNTRL input can also be
used to interrupt charging and allow the microcontroller to
measure the cell voltage under a normal condition to get a
more accurate measure of the battery voltage. Once the over
voltage is removed, the NCP345 will turn on the MOSFET.
The turn on circuitry is designed to turn on the MOSFET
more gradually to limit the inrush current. Typical turnon
performance is illustrated using the MGSF3441 in Figure 7.
This characteristic is a function of the threshold of the
MOSFET and will vary depending on the device
characteristics such as the gate capacitance.
The OVP has an under voltage lockout (UVLO) circuit
which disables the gate driver circuit until the UVLO senses
that the V
CC
voltage is above 2.6 V. Once the UVLO has
released the gate driver circuit, the OUT signal will stay high
until the voltage on the IN is sensed. If the input voltage to
IN is less than 6.85 V nominal, then the OUT signal will be
driven LOW and the FET will be turned on so the source can
be connected to the load.
There are three events that will cause the OVP to drive the
gate of the FET to a HIGH state.
Voltage on V
CC
falls below the UVLO threshold
Voltage on IN rises above 6.85 V (nominal)
CNTRL input is driven to a logic High
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1651DR2G | Single Stage Power Factor Controller |
| NCP345SNT1G | Overvoltage Protection IC |
| NCP346SN1T1G | Overvoltage Protection IC |
| NCP346SN2T1G | Overvoltage Protection IC |
| NCP3488DR2G | MOSFET Driver with Dual Outputs for Synchronous Buck Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1651DR2 | 功能描述:功率因數校正 IC Single Stage PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1651DR2G | 功能描述:功率因數校正 IC Single Stage PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652ADR2G | 功能描述:功率因數校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652DR2G | 功能描述:功率因數校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652DWR2G | 功能描述:功率因數校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。