參數資料
型號： NCP1207BDR2G
廠商： ON SEMICONDUCTOR
元件分類： 穩壓器
英文描述： PWM Current-Mode Controller for Free Running Quasi-Resonant Operation
中文描述： 0.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO7
封裝： LEAD FREE, SOIC-8/7
文件頁數： 12/15頁
文件大?。?/td> 264K
代理商： NCP1207BDR2G
NCP1207B
http://onsemi.com
12
If the power consumption budget is really too high for the
DSS alone, connect a diode between the auxiliary
winding and the V
CC
pin which will disable the DSS
operation (V
CC
10 V).
The SOIC package offers a 178
°
C/W thermal resistor.
Again, adding some copper area around the PCB footprint
will help decrease this number: 12 mm
R
JA
down to 100
°
C/W with 35 m copper thickness (1 oz)
or 6.5 mm
6.5 mm with 70 m copper thickness (2 oz).
As one can see, we do not recommend using the SO-8
package and the DSS if the part operates at high switching
frequencies. In that case, an auxiliary winding is the best
solution.
12 mm to drop
Overload Operation
In applications where the output current is purposely not
controlled (e.g. wall adapters delivering raw DC level), it is
interesting to implement a true short-circuit protection. A
short-circuit actually forces the output voltage to be at a low
level, preventing a bias current to circulate in the
Optocoupler LED. As a result, the FB pin level is pulled up
to 4.2 V, as internally imposed by the IC. The peak current
setpoint goes to the maximum and the supply delivers a
rather high power with all the associated effects. Please note
that this can also happen in case of feedback loss, e.g. a
broken Optocoupler. To account for this situation,
NCP1207B hosts a dedicated overload detection circuitry.
Once activated, this circuitry imposes to deliver pulses in a
burst manner with a low duty-cycle. The system recovers
when the fault condition disappears.
During the startup phase, the peak current is pushed to the
maximum until the output voltage reaches its target and the
feedback loop takes over. This period of time depends on
normal output load conditions and the maximum peak
current allowed by the system. The time-out used by this IC
works with the V
CC
decoupling capacitor: as soon as the
V
CC
decreases from the VCC
OFF
level (typically 12 V) the
device internally watches for an overload current situation.
If this condition is still present when the VCC
ON
level is
reached, the controller stops the driving pulses, prevents the
self-supply current source to restart and puts all the circuitry
in standby, consuming as little as 330 A typical (I
CC3
parameter). As a result, the V
CC
level slowly discharges
toward 0. When this level crosses 5.3 V typical, the
controller enters a new startup phase by turning the current
source on: V
CC
rises toward 12 V and again delivers output
pulses at the VCC
OFF
crossing point. If the fault condition
has been removed before VCC
ON
approaches, then the IC
continues its normal operation. Otherwise, a new fault cycle
takes place. Figure 24 shows the evolution of the signals in
presence of a fault.
If the fault is relaxed during the Vcc
natural fall down sequence, the IC
automatically resumes.
If the fault still persists when Vcc
reached VCC
ON
, then the controller
cuts everything off until recovery.
Figure 24.
TIME
TIME
TIME
INTERNAL
FAULT FLAG
V
CC
12 V
10 V
5.3 V
DRV
DRIVER
PULSES
FAULT IS
RELAXED
FAULT OCCURS HERE
STARTUP PHASE
REGULATION
OCCURS HERE
LATCHOFF
PHASE
Soft-Start
The NCP1207B features an internal 1 ms soft-start to
soften the constraints occurring in the power supply during
startup. It is activated during the power on sequence. As
soon as V
CC
reaches VCC
OFF
, the peak current is gradually
increased from nearly zero up to the maximum clamping
level (e.g. 1.0 V). The soft-start is also activated during the
overcurrent burst (OCP) sequence. Every restart attempt is
followed by a soft-start activation. Generally speaking, the
soft-start will be activated when V
CC
ramps up either from
zero (fresh power-on sequence) or 5.3 V, the latchoff
voltage occurring during OCP.
相關PDF資料
PDF描述
NCP1207 PWM Current-Mode Controller for Free Running Quasi-Resonant Operation(電流模式控制的PWM控制器，用于自由振蕩的“準諧振”操作)
NCP1209 PWM Voltage Mode Controller(電壓模式控制的PWM控制器)
NCP1212DR2G Current Mode PWM Controller for Both Forward and Flyback Converters
NCP1212 Current Mode PWM Controller for Both Forward and Flyback Converters
NCP1212PG Current Mode PWM Controller for Both Forward and Flyback Converters
相關代理商/技術參數
參數描述
NCP1207-D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:PWM Current-Mode Controller for Free Running Quasi-Resonant Operation
NCP1207DR2 功能描述:IC CTRLR PWM CM OVP OCP HV 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR
NCP1207DR2G 功能描述:IC CTRLR PWM CM OVP OCP HV 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR
NCP1207P 功能描述:IC CTRLR PWM CM OVP OCP HV 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR
NCP1207PG 功能描述:IC CTRLR PWM CM OVP OCP HV 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:- 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*