- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCP1080DEG (ON Semiconductor)IC CONV CTLR POE-PD 13W 20-TSSOP Datasheet資料下載
參數資料
| 型號： | NCP1080DEG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 221K |
| 描述： | IC CONV CTLR POE-PD 13W 20-TSSOP |
| 標準包裝： | 74 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 是 |
| 電流限制： | 500mA |
| 電源電壓： | 0 V ~ 57 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 20-TSSOP-EP |
| 包裝： | 管件 |
NCP1080
http://onsemi.com
10
DESCRIPTION OF OPERATION
Powered Device Interface
The PD interface portion of the NCP1080 supports the
IEEE802.3af defined operating modes: detection signature,
current source classification, inrush and operating current
limits. In order to give more flexibility to the user and also
to keep control of the power dissipation in the NCP1080,
both current limits are configurable. The device enters
operation once its programmable Vuvlo_on threshold is
reached, and operation ceases when the supplied voltage
falls below the Vuvlo_off threshold. Sufficient hysteresis
and Uvlo filter time are provided to avoid false power on/off
cycles due to transient voltage drops on the cable.
Detection
During the detection phase, the incremental equivalent
resistance seen by the PSE through the cable must be in the
IEEE802.3af standard specification range (23.75 kW to
26.25 kW) for a PSE voltage from 2.7 V to 10.1 V. In order
to compensate for the nonlinear effect of the diode bridge
and satisfy the specification at low PSE voltage, the
NCP1080 presents a suitable impedance in parallel with the
25.5 kW R
det
external resistor connected between VPORTP
and VPORTN. For some types of diodes (especially
Schottky diodes), it may be necessary to adjust this external
resistor.
When the Detection_Off level is detected (typically
11.5 V) on VPORTP, the NCP1080 turns on its internal
3.3 V regulator and biasing circuitry in anticipation of the
classification phase as the next step.
Classification
Once the PSE device has detected the PD device, the
classification process begins. In classification, the PD
regulates a constant current source that is set by the external
resistor RCLASS value on the CLASS pin. Figure 6 shows
the schematic overview of the classification block. The
current source is defined as:
I
class
+
V
bg
R
class
, (where V
bg
is 1.2 V)
CLASS
VDDA1
1.2 V
VPORTP
VPORTN1,2
NCP1080
Rclass
Figure 6. Classification Block Diagram
Power Mode
When the classification handshake is completed, the
PSE and PD devices move into the operating mode.
Under Voltage Lock Out (UVLO)
The NCP1080 incorporates an under voltage lock out
(UVLO) circuit which monitors the input voltage and
determines when to apply power to the DCDC controller.
To use the default settings for UVLO (see Table 3), the pin
UVLO must be connected to VPORTN
1,2
. In this case the
signature resistor has to be placed directly between
VPORTP and VPORTN
1,2
, as shown in Figure 7.
Figure 7. Default UVLO Settings
UVLO
VPORTP
VPORTN1,2
NCP1080
VPORT
Rdet
To define the UVLO threshold externally, the UVLO pin
must be connected to the center of an external resistor
divider between VPORTP and VPORTN
1,2
as shown in
Figure 8. The series resistance value of the external resistors
must add to 25.5 kW and replaces the internal signature
resistor.
Figure 8. External UVLO Configuration
UVLO
VPORTN1,2
NCP1080
VPORT
R2
R1
VPORTP
For a Vuvlo_on desired turnon voltage threshold, R1 and
R2 can be calculated using the following equations:
R1 ) R2 + R
det
R2 +
1.2
V
ulvo_on
R
det
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1081DEG | IC CONV CTLR POE-PD 40W 20-TSSOP |
| NCP1082DEG | IC CONV CTLR POE-PD 13W 20-TSSOP |
| NCP1083DEG | IC CONV CTLR POE-PD 40W 20-TSSOP |
| NCP1501DMR2G | IC REG SGL BUCK/LINEAR 8MICRO |
| NCP1578MNR2G | IC REG DL BCK/LINEAR SYNC 20-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1080DER2G | 功能描述:直流/直流開關轉換器 POE-PD 13W DC-DC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1081 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Integrated High Power PoE-PD Interface & DC-DC Converter Controller |
| NCP1081DEG | 功能描述:DC/DC 開關控制器 POE-PD 40W DC-DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP1081DER2G | 功能描述:DC/DC 開關控制器 POE-PD 40W DC-DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP1081SPCGEVB | 功能描述:電源管理IC開發工具 HPOWER POE-PD SPLITTER RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。