CRD_I/O i" />
參數資料
型號: NCN4557MTR2G
廠商: ON Semiconductor
文件頁數: 3/12頁
文件大?。?/td> 0K
描述: IC SMART CARD/SIM DUAL 16-QFN
標準包裝: 3,000
系列: *
應用: *
接口: *
電源電壓: *
封裝/外殼: 16-WFQFN 裸露焊盤
供應商設備封裝: 16-QFN(3x3)
包裝: 帶卷 (TR)
安裝類型: 表面貼裝
NCN4557
http://onsemi.com
11
this state or 8
ms after the ENABLE pin is set LOW in
the other cases.
CRD_I/O is forced to LOW about 8 ms after the
ENABLE pin is set LOW.
Then CRD_VCC Supply Shuts Off
Figure 13. NCN4557 Power Down Sequence
CRD_VCCA/B
CRD_IOA/B
CRD_CLKA/B
CRD_RSTA/B
ENABLE
TOFF ~ 8.0 ms
Input Schmitt Triggers
All the logic input pins (excepted I/O and CRD_I/O,
Figure 3) have builtin Schmitt trigger circuits to prevent
the NCN4557 against uncontrolled operation. The typical
dynamic characteristics of the related pins are depicted in
Figure 14.
OUTPUT
VDD
ON
OFF
0.2 x VDD
or
0.4 V
0.7 x VDD
INPUT
Figure 14. Typical Schmitt Trigger Characteristics
Shutdown Operating
In order to save power or for other purpose required by
the application it is possible to put the NCN4557 in a
shutdown mode by setting LOW the pin ENABLE. On the
other hand the device enters automatically in a shutdown
mode when VDD becomes lower than 1.0 V typically.
ESD Protection
The NCN4557 CRD interface features an Human Body
Model ESD voltage protection in excess of 8 kV for all the
CRD
pins
(CRD_IOA
&
B,
CRD_CLKA
&
B,
CRD_RSTA & B, CRD_VCCA & B and GND). All the
other pins (microcontroller side) sustain at least 2 kV.
These values are guaranteed for the device in its full
integrity without considering the external capacitors added
to the circuit for a proper operating. Consequently in the
operating conditions it is able to sustain much more than
8 kV on its CRD pins making it perfectly protected against
electrostatic discharge well over the Human Body Model
ESD voltages required by the ISO7816 standard (4 kV).
Printed Circuit Board Layout
Careful layout routing will be applied to achieve a good
and efficient operating of the device in its mobile or
portable environment and fully exploit its performance.
The bypass capacitors have to be connected as close as
possible to the device pins (CRD_VCCA and B, VDD or
VBAT) in order to reduce as much as possible parasitic
behaviors (ripple and noise). It is recommended to use
ceramic capacitors.
The exposed pad of the QFN16 package will be
connected to the ground. A relatively large ground plane is
recommended.
ORDERING INFORMATION
Device
Package
Shipping
NCN4557MTG
QFN16
(PbFree)
123 Units / Rail
NCN4557MTR2G
QFN16
(PbFree)
3000 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
相關PDF資料
PDF描述
PIC16C54A-20/SS IC MCU OTP 512X12 20SSOP
VE-B0P-IX-F3 CONVERTER MOD DC/DC 13.8V 75W
D38999/26WE26HA CONN PLUG 26POS STRAIGHT W/PINS
PIC18LF45K80-I/P MCU PIC ECAN 32KB FLASH 40DIP
VI-J4N-IW-F1 CONVERTER MOD DC/DC 18.5V 100W
相關代理商/技術參數
參數描述
NCN-4-8-2 制造商:z*INACTIVE* NATIONAL 功能描述:
NCN49597 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power Line Carrier Modem
NCN49597ID11EVB 制造商:ON Semiconductor 功能描述:EVAL BOARD - Bulk
NCN49597MNG 功能描述:通信集成電路 - 若干 9.6 KBDS FLEX PLC MODEM RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
NCN49597MNRG 功能描述:IC PLC MODEM FLEX 9.6KBDS 52-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:* 標準包裝:25 系列:- 數據格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574