- 您現在的位置：買賣IC網 > PDF目錄369935 > MUN2211 (ON SEMICONDUCTOR) NPN SILICON BIAS RESISTOR TRANSISTOR PDF資料下載
參數資料
| 型號： | MUN2211 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | NPN SILICON BIAS RESISTOR TRANSISTOR |
| 中文描述： | NPN硅偏置電阻晶體管 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 263K |
| 代理商： | MUN2211 |
9
Motorola Small–Signal Transistors, FETs and Diodes Device Data
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
mm
inches
2.5–3.0
0.039
1.0
0.094
2.4
0.8
0.098–0.118
0.031
0.95
0.037
0.95
0.037
SC–59 POWER DISSIPATION
The power dissipation of the SC–59 is a function of the pad
size. This can vary from the minimum pad size for soldering
to the pad size given for maximum power dissipation. Power
dissipation for a surface mount device is determined by
TJ(max), the maximum rated junction temperature of the die,
R
θ
JA, the thermal resistance from the device junction to
ambient; and the operating temperature, TA. Using the
values provided on the data sheet, PD can be calculated as
follows:
PD =
TJ(max) – TA
R
θ
JA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25
°
C, one can
calculate the power dissipation of the device which in this
case is 200 milliwatts.
PD =150
°
C – 25
°
C
625
°
C/W
= 200 milliwatts
The 625
°
C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve a
power dissipation of 200 milliwatts. Another alternative would
be to use a ceramic substrate or an aluminum core board
such as Thermal Clad
. Using a board material such as
Thermal Clad, a power dissipation of 400 milliwatts can be
achieved using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10
°
C.
The soldering temperature and time should not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient should be 5
°
C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相關PDF資料 |
PDF描述 |
|---|---|
| MUN2212 | NPN SILICON BIAS RESISTOR TRANSISTOR |
| MUN2212T1 | NPN SILICON BIAS RESISTOR TRANSISTOR |
| MUN2213 | NPN SILICON BIAS RESISTOR TRANSISTOR |
| MUN22xxT1 | NPN SILICON BIAS RESISTOR TRANSISTOR |
| MUN2231T1 | NPN SILICON BIAS RESISTOR TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MUN2211_09 | 制造商:WEITRON 制造商全稱:Weitron Technology 功能描述:NPN Silicon Bias Resistor Transistor |
| MUN2211JT1 | 功能描述:TRANS BRT NPN 100MA 50V SC-59 RoHS:否 類別:分離式半導體產品 >> 晶體管(BJT) - 單路﹐預偏壓式 系列:- 標準包裝:10,000 系列:- 晶體管類型:NPN - 預偏壓 電流 - 集電極 (Ic)（最大）:100mA 電壓 - 集電極發射極擊穿（最大）:50V 電阻器 - 基極 (R1)（歐）:47k 電阻器 - 發射極 (R2)（歐）:47k 在某 Ic、Vce 時的最小直流電流增益 (hFE):70 @ 5mA，5V Ib、Ic條件下的Vce飽和度（最大）:300mV @ 500µA，10mA 電流 - 集電極截止（最大）:- 頻率 - 轉換:100MHz 功率 - 最大:250mW 安裝類型:表面貼裝 封裝/外殼:SC-70，SOT-323 供應商設備封裝:PG-SOT323-3 包裝:帶卷 (TR) 其它名稱:SP000756242 |
| MUN2211JT1G | 功能描述:開關晶體管 - 偏壓電阻器 SS BR XSTR NPN 50V RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
| MUN2211RT1 | 制造商:LRC 制造商全稱:Leshan Radio Company 功能描述:Bias Resistor Transistor |
| MUN2211T1 | 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT NPN RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。