- 您現在的位置：買賣IC網 > PDF目錄359238 > MULTISYNCFE750 Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A PDF資料下載
參數資料
| 型號： | MULTISYNCFE750 |
| 英文描述： | Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| 中文描述： | Monitor_ICs：HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| 文件頁數： | 49/52頁 |
| 文件大?。?/td> | 517K |
| 代理商： | MULTISYNCFE750 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁
MON08 Multilink User Manual
49
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
analyzing the reset of the status bits.
1 – Device echoed some security bytes:
The monitor resident in a 68HC08 device automatically echoes every
incoming character when it is in monitor mode. A valid character
transmitted from the PC should be echoed once by the loopback circuitry
on the board and once by the monitor of the target processor itself. This
status indicates whether or not the second echoed character from the
monitor response was received when one of the security bytes was
transmitted. If the status is ‘N’, which indicates that the character was not
received, or not received properly, it is most likely due to one of the
following reasons:
1. The baud rate specified was incorrect.
2. The part did not start the monitor mode security check on reset.
Signals to force monitor mode may be incorrect.
3. No Power to the ICS.
If this status bit responded with an ‘N’, you must correct this before
analyzing the reset of the status bits.
2 – Device echoed all security bytes:
In order to pass security, the software must send 8 security bytes to the
processor. The processor should echo each of these eight bytes twice. If all
8 bytes did not get the proper two-byte echo, this flag will be ‘N’. Reasons
for this include:
1. The part did not start the monitor mode security check on reset.
Signals to force monitor mode may be incorrect.
2. The baud rate specified was incorrect.
3. The processor was not reset properly. Check the “Target Hardware
Type” and if you are connecting to a class II board, check the “MON08
cable communication connections type” in the “advanced settings”
dialog.
3 – Device signaled monitor mode with a break:
Once the processor has properly received the 8 bytes from the PC software
to complete its security check, it should transmit a break character to the
PC signaling entry into monitor mode. This break should be sent regardless
of whether the security check was successfully passed. If a break was not
received from the processor, this flag will be ‘N’. Reasons for this include:
1. The baud rate specified was incorrect.
2. The processor was not reset properly. Check the “Target Hardware
相關PDF資料 |
PDF描述 |
|---|---|
| MUM8128W-17 | x8 EPROM |
| MUM8128W-20 | x8 EPROM |
| MUM8128W-25 | x8 EPROM |
| MUM8128WI-17 | x8 EPROM |
| MUM8128WI-20 | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MULTI-TC | 制造商:ERSA 功能描述:SOLDERING IRON 230V 75W EURO PLUG 制造商:ERSA 功能描述:SOLDERING IRON, 230V, 75W, EURO PLUG |
| MULTI-TEST | 制造商:L COM 功能描述:PC CABLE TESTER ATA 制造商:L-com Inc 功能描述:PC CABLE TESTER ATA |
| MULTI-USE LIGHT | 制造商:Energizer Battery Company 功能描述: |
| MULTIWATT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT |
| MULTIWATT11 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT |
發布緊急采購，3分鐘左右您將得到回復。