- 您現在的位置：買賣IC網 > PDF目錄359238 > MULTILINK08UM MON08 Multilink Hardware Manual PDF資料下載
參數資料
| 型號： | MULTILINK08UM |
| 英文描述： | MON08 Multilink Hardware Manual |
| 中文描述： | 的MON08多重硬件手冊 |
| 文件頁數： | 46/52頁 |
| 文件大?。?/td> | 517K |
| 代理商： | MULTILINK08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁
46
MON08 Multilink User Manual
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
reset.
MON08 Cable connection communications type (Class II boards Only)
This selection box is valid only for Class II hardware configurations using the
MON08 cable. It allows the user to specify the sequence that the software uses
to power up the ICS system. When the software tries to create a power-on reset
condition, two events must occur:
1. Power of the target MCU must go below 0.1v. This means that the
processor can not be receiving power from its power pins, nor can it have a
significant voltage being driven on port pins or the IRQ line, as these will
drive the MCU power back through these pins. It is crucial, therefore, to
have the ICS and the Target both powered down at some point in time.
2. The processor MON08 configuration pins, including IRQ, must be
properly driven when the target processor resets to drive it into monitor
mode. If these pins are not set up properly before the processor powers up,
the processor may start up in user mode.
PowerDown ICS, Ask the user to power down their board, PowerUp ICS,
Ask the user to power up their board
This is the default option and should work for most, if not all, ICS08/Target
Board solutions. Refer to the manual addendum under startup for the settings
for a specific ICS board. It requires the user go through two dialog stages, and
requires more time than simply cycling the power.
1. Software automatically powers down the ICS.
2. Software Asks the user to power down the board as follows:
Figure 4-45: Power Down Dialog
3. Software automatically powers up the ICS, which configures the
processor’s MON08 configuration pins.
4. Software asks the user to power up the board as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| MULTILYNX | MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver |
| MULTISYNCFE750 | Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| MUM8128W-17 | x8 EPROM |
| MUM8128W-20 | x8 EPROM |
| MUM8128W-25 | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MULTILYNX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver |
| MULTIMAX-8G+ | 功能描述:程序設計器 - 基于通用和內存 HI PERF STAND ALONE PRGRAMER FOR 8-SOCK RoHS:否 制造商:Xeltek 產品:Universal Device Programmers 工具用于評估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口類型:Parallel, USB 工作電源電壓:90 VAC to 250 VAC |
| MULTIPHSPOL-RD | 功能描述:電源管理IC開發工具 Si825x Multi-Phase POL Reference Design RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。