- 您現在的位置：買賣IC網 > PDF目錄359238 > MULTILINK08UM MON08 Multilink Hardware Manual PDF資料下載
參數資料
| 型號： | MULTILINK08UM |
| 英文描述： | MON08 Multilink Hardware Manual |
| 中文描述： | 的MON08多重硬件手冊 |
| 文件頁數： | 45/52頁 |
| 文件大?。?/td> | 517K |
| 代理商： | MULTILINK08UM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
MON08 Multilink User Manual
45
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
settings dialog.
Figure 4-44: Target Hardware Type: Advanced Settings Dialog
Tpd and Tpu Timing
These timing parameters are mostly designed for Class I boards, although the
delays are valid for all classes of boards. Many of the ICS boards and user
target boards need time to power down and power up.
Whenever power is automatically switched off, or is manually requested to be
switched off, the software waits for an amount of time equal to the Tpd delay
time before proceeding to the connection protocol. This is because a board or
power supply may have capacitance which holds the power up for a short time
after the supply has been switched off, but the supply voltage must reach less
than 0.1v before it is turned back on if a Power-On reset is to occur.
Whenever power is automatically switched on, or is manually requested to be
switched on, the software waits for an amount of time equal to the Tpu delay
time before attempting to contact the 68HC08 processor. This is to allow time
not only for power to be fully available, but to wait until any reset driver has
finally released the RESET line. On many ICS08 boards (such as the
ICS08RK, M68ICS08JL3, M68ICS08JLJK, and ICS08GP20) the Tpu can be
decreased to as little as 250ms with no adverse effects.
Target has RESET button (class III boards only):
The software
occasionally needs to get control of the target. On systems which are Class III
boards with the monitor mode circuitry built-in (including RS-232 driver),
there is no means to reset the target to gain control. If the board has a reset
button, the software can use this to gain control of the target system. If this
option is checked, the software will prompt the user to push the target reset
button when a reset of the target system is desired. If the option is unchecked,
the software will ask the user to power cycle the target system to achieve a
相關PDF資料 |
PDF描述 |
|---|---|
| MULTILYNX | MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver |
| MULTISYNCFE750 | Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| MUM8128W-17 | x8 EPROM |
| MUM8128W-20 | x8 EPROM |
| MUM8128W-25 | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MULTILYNX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MultiLynx CL2151 Universal HFC? Interactive Cable Transceiver |
| MULTIMAX-8G+ | 功能描述:程序設計器 - 基于通用和內存 HI PERF STAND ALONE PRGRAMER FOR 8-SOCK RoHS:否 制造商:Xeltek 產品:Universal Device Programmers 工具用于評估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口類型:Parallel, USB 工作電源電壓:90 VAC to 250 VAC |
| MULTIPHSPOL-RD | 功能描述:電源管理IC開發工具 Si825x Multi-Phase POL Reference Design RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。