- 您現在的位置：買賣IC網 > PDF目錄376207 > MTP805S (Electronic Theatre Controls, Inc.) 8051 Embedded USB/PS2 Keyboard/Mouse Controller PDF資料下載
參數資料
| 型號： | MTP805S |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| 中文描述： | 8051嵌入式USB/PS2鍵盤/鼠標控制器 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 125K |
| 代理商： | MTP805S |
MYSON
TECHNOLOGY
MTP805
(Rev. 0.9)
Revision 0.9 - 8 - 2000/07/19
receive interrupt (RC0I). S/W can read the EP0STUS register for the recent transfer information, which
includes the data byte count (RC0cnt), data direction (EP0dir), SETUP token flag (EP0set) and data valid
flag (RC0err). The received data is always stored into RC0FIFO and the RC0cnt is always updated for DATA
packets following SETUP tokens. The data following an OUT token is written into the RC0FIFO, and the
RC0cnt is updated unless Endpoint 0 STALL (EP0stall) is set or Endpoint 0 receive ready (RC0rdy) is
cleared. The SIE clears the RC0rdy automatically and generates RC0I interrupt when the RC0cnt/RC0FIFO
is updated. As long as the RC0rdy is cleared, SIE keep responding NAK to Host’s Endpoint 0 OUT packet
request. S/W should set the RC0rdy flag after the RC0I interrupt is asserted and RC0FIFO is read out.
8.3 Endpoint 0 transmit
After detecting a valid Endpoint 0 IN token, MTP805 automatically transmit the data pre-stored in the
Endpoint 0 transmit FIFO (TX0FIFO) to the USB bus if the Endpoint 0 transmit ready flag (TX0rdy) is set and
the EP0stall is cleared. The number of byte to be transmitted is base on the Endpoint 0 transmit byte count
register (TX0cnt). The DATA0/1 token to be transmitted is base on the Endpoint 0 transmit toggle control bit
(TX0tgl). After the TX0FIFO is updated, TX0rdy should be set to 1. This enables the MTP805 to respond to
an Endpoint 0 IN packet. TX0rdy is cleared and an Endpoint 0 transmit interrupt (TX0I) is generated once the
USB host acknowledges the data transmission. The interrupt service routine can check TX0rdy to confirm
that the data transfer was successful.
8.4 Endpoint 1/2 transmit
Endpoint1 and Endpoint2 are capable of transmit only. These endpoints are enable when the Endpoint1/
Endpoint2 configured control bit (EP1cfgd/EP2cfgd) is set. After detecting a valid Endpoint 1/2 IN token,
MTP805 automatically transmit the data pre-stored in the Endpoint 1/2 transmit FIFO (TX1FIFO/TX2FIFO) to
the USB bus if the Endpoint 1/2 transmit ready flag (TX1rdy/TX2rdy) is set and the EP1stall/EP2stall is
cleared. The number of byte to be transmitted is base on the Endpoint 1/2 transmit byte count register
(TX1cnt/TX2cnt). The DATA0/1 token to be transmitted is base on the Endpoint 1/2 transmit toggle control
bit (TX1tgl/TX2tgl). After the TX1FIFO/TX2FIFO is updated, TX1rdy/TX2rdy should be set to 1. This enables
the MTP805 to respond to an Endpoint 1/2 IN packet. TX1rdy/TX2rdy is cleared and an Endpoint 1/2
transmit interrupt (TX1I/TXI2) is generated once the USB host acknowledges the data transmission. The
interrupt service routine can check TX1rdy/TX2rdy to confirm that the data transfer was successful.
8.5 USB Control and Status
Other USB control bits include the USB enable (ENUSB), SUSPEND (Susp), RESUME (RsmO), Control
Read (CtrRD), and corresponding interrupt enable bits. The CtrRD should be set when program detects the
current transfer is an Endpoint0 Control Read Transfer. Once this bit is set, the MTP805 will stall an
Endpoint0 OUT packet with DATA toggle 0 or byte count other than 0. Other USB status flag includes the
USB reset interrupt (RstI), RESUME interrupt (RsmI), and USB Suspend interrupt (SusI).
8.6 Suspend and Resume
Once the Suspend condition is asserted, S/W can set the Susp bit to stop the USBSIE's clock. In the mean
time, the 3.3V Regulator is operating in low power mode. S/W can further save the device power by force the
8051 CPU core into the Power Down or Idle mode by setting the PCON register in SFR area. In the Idel
mode, the X'tal keeps oscillating and CPU can be waken-up by the trigger of any enabled interrupt. In the
Power Down mode, the X'tal is stop, but CPU can be waken-up by the trigger of enabled interrupt's source.
In short, S/W can keep the RsmI/KbdI/MsI alive before enter the suspend mode.
The MTP805 send Resume signaling to USB bus when Susp=1 and RSMO=1. In the suspend mode, if a
keyboard or mouse interrupt is asserted, S/W should send resume signal to wake up the USB bus.
相關PDF資料 |
PDF描述 |
|---|---|
| MTP805V | 8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTU429B | 4-Bit Micro-Controller with LCD Dr |
| MTU8B57EM | EPROM-Based 8-Bit CMOS Microcontroller |
| MTU8B54E | EPROM-Based 8-Bit CMOS Microcontroller |
| MTU8B54EN | EPROM-Based 8-Bit CMOS Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MTP805V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8051 Embedded USB/PS2 Keyboard/Mouse Controller |
| MTP810G | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:MODULAR TELEPHONE PLUGS |
| MTP810U | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:MODULAR TELEPHONE PLUGS |
| MTP810W | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:MODULAR TELEPHONE PLUGS |
| MTP84G | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:MODULAR TELEPHONE PLUGS |
發布緊急采購，3分鐘左右您將得到回復。