- 您現在的位置：買賣IC網 > PDF目錄383645 > MT9076AB (Mitel Networks Corporation) T1/E1/J1 3.3V Single Chip Transceiver PDF資料下載
參數資料
| 型號： | MT9076AB |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | T1/E1/J1 3.3V Single Chip Transceiver |
| 中文描述： | T1/E1/J1收發3.3V的單芯片收發器 |
| 文件頁數： | 43/160頁 |
| 文件大?。?/td> | 416K |
| 代理商： | MT9076AB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁
Preliminary Information
MT9076
39
dual byte address is being received. If this bit is 0 then a two byte address is being received and then only the
first six bits of the first address byte are compared. An all call condition is also monitored for the second
address byte; and if received the first address byte is ignored (not compared with mask byte). If the address
extension bit is a 1 then a single byte address is being received. In this case, an all call condition is monitored
for in the first byte as well as the mask byte written to the comparison register and the second byte is ignored.
Seven bits of address comparison can be realized on the first byte if this is a single byte address by setting the
Seven bit of Control Register 2.
The following two Status Register bits (RQ8 and RQ9) are appended to each data byte as it is written to the Rx
FIFO. They indicate that a good packet has been received (good FCS and no frame abort), or a bad packet
with either incorrect FCS or frame abort. The Status and Interrupt Registers should be read before reading the
Rx FIFO since status and interrupt information correspond to the byte at the output of the FIFO (i.e. the byte
about to be read). The Status Register bits are encoded as follows:
RQ9
1
0
1
0
RQ8
1
1
0
0
Byte status
last byte (bad packet)
first byte
last byte (good packet)
packet byte
The end-of-packet-detect (EOPD) interrupt indicates that the last byte written to the Rx FIFO was an EOP byte
(last byte in a packet). The end-of-packet-read (EopR) interrupt indicates that the byte about to be read from
the Rx FIFO is an EOP byte (last byte in a packet). The Status Register should be read to see if the packet is
good or bad before the byte is read.
A minimum size packet has an 8-bit address, an 8-bit control byte, and a 16-bit FCS pattern between the
opening and closing flags (see Section 9.3.2). Thus, the absence of a data transmission error and a frame
length of at least 32 bits results in the receiver writing a valid packet code with the EOP byte into Rx FIFO. The
last 16 bits before the closing flag are regarded as the FCS pattern and will not be transferred to the receiver
FIFO. Only data bytes (Address, Control, Information) are loaded into the Rx FIFO.
In the case of an Rx FIFO overflow, no clocking occurs until a new opening flag is received. In other words, the
remainder of the packet is not clocked into the FIFO. Also, the top byte of the FIFO will not be written over. If
the FIFO is read before the reception of the next packet then reception of that packet will occur. If two
beginning of packet conditions (RQ9=0;RQ8=1) are seen in the FIFO, without an intermediate EOP status,
then overflow occurred for the first packet.
The receiver may be enabled independently of the transmitter. This is done by setting the RXEN bit of Control
Register 1. Enabling happens immediately upon writing to the register. Disabling using RXEN will occur after
the present packet has been completely loaded into the FIFO. Disabling can occur during a packet if no bytes
have been written to the FIFO yet. Disabling will consist of disabling the internal receive clock. The FIFO,
Status, and Interrupt Registers may still be read while the receiver is disabled. Note that the receiver requires a
flag before processing a frame, thus if the receiver is enabled in the middle of an incoming packet it will ignore
that packet and wait for the next complete one.
The receive CRC can be monitored in the Rx CRC Registers. These registers contain the actual CRC sent by
the other transmitter in its original form; that is, MSB first and bits inverted. These registers are updated by
each end of packet (closing flag) received and therefore should be read when an end of packet is received so
that the next packet does not overwrite the registers.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9076 | T1/E1/J1 3.3V Single Chip Transceiver(T1/E1/J1 3.3V 單片收發器) |
| MT9079 | Advanced Controller for E1(先進的E1幀調節器和控制器) |
| MT9080B | SMX - Switch Matrix Module(用于消費類轉換應用的開關矩陣模塊) |
| MT90810 | Flexible MVIP(Multi-Vendor Integration Protocol) Interface Circuit(彈性MVIP接口電路) |
| MT90812 | Integrated Digital Switch (IDX)(集成數字開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9076AP | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/J1 3.3V Single Chip Transceiver |
| MT9076B | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
| MT9076BB | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BB1 | 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/J1/T1 3.3V 80LQFP - Trays |
| MT9076BP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1/J1 3.3 V Single Chip Transceiver |
發布緊急采購，3分鐘左右您將得到回復。