參數資料
型號： MT9042C
廠商： Mitel Networks Corporation
英文描述： Multitrunk System Synchronizer(多中繼系統同步裝置)
中文描述： Multitrunk系統同步器（多中繼系統同步裝置）
文件頁數： 8/28頁
文件大?。?/td> 126K
代理商： MT9042C
MT9042C
8
Automatic Control
Automatic Control should be used when simple
MT9042C control is required, which is more complex
than the very simple control provide by Manual
Control with no external circuitry, but not as complex
as Manual Control with a microcontroller.
example, simple control could include operation in a
system
which
can
be
Automatic Control State Diagram shown in Figure 8.
For
accommodated
by
the
Automatic Control is also selected by mode/control
pins MS2 and MS1. However, the mode and active
reference source is selected automatically by the
internal Automatic State Machine (See Figure 6).
The mode and reference changes are based on the
logic levels on the LOS1, LOS2 and GTi control pins.
Refer to Table 5 and Figure 8 for details of the state
change sequences.
Normal Mode
Normal Mode is typically used when a slave clock
source, synchronized to the network is required.
In Normal Mode, the MT9042C provides timing
(C1.5o, C2o, C3o, C4o, C8o and C16o) and frame
synchronization (F0o, F8o, F16o) signals, which are
synchronized to one of two reference inputs (PRI or
SEC).
The input reference signal may have a
nominal frequency of 8kHz, 1.544MHz or 2.048MHz.
From a reset condition, the MT9042C will take up to
25 seconds for the output signal to be phase locked
to the selected reference.
The
dependent as shown in state tables 4 and 5.
reference frequencies are selected by the frequency
control pins FS2 and FS1 as shown in Table 1.
selection
of
input
references
is
control
The
Holdover Mode
Holdover Mode is typically used for short durations
(e.g., 2 seconds) while network synchronization is
temporarily disrupted.
In Holdover Mode, the MT9042C provides timing and
synchronization signals, which are not locked to an
external reference signal, but are based on storage
techniques. The storage value is determined while
the device is in Normal Mode and locked to an
external reference signal.
When in Normal Mode, and locked to the input
reference signal, a numerical value corresponding to
the MT9042C output frequency is stored alternately
in two memory locations every 30ms.
device is switched into Holdover Mode, the value in
memory from between 30ms and 60ms is used to set
the output frequency of the device.
When the
The
±
0.05ppm, which translates to a worst case 35 frame
(125us) slips in 24 hours.
TR62411 Stratum 3 requirement of
±
0.37ppm (255
frame slips per 24 hours).
frequency
accuracy
of
Holdover
Mode
is
This exceeds the AT&T
Two factors affect the accuracy of Holdover Mode.
One is drift on the Master Clock while in Holdover
Mode, drift on the Master Clock directly affects the
Holdover Mode accuracy.
Master Clock (OSCi) accuracy does not affect
Holdover
accuracy,
only
accuracy while in Holdover. For example, a
±
32ppm
master clock may have a temperature coefficient of
±
0.1ppm per degree C. So a 10 degree change in
temperature, while the MT9042C is in Holdover
Mode may result in an additional offset (over the
±
0.05ppm) in frequency accuracy of
±
1ppm. Which
is much greater than the
±
0.05ppm of the MT9042C.
Note that the absolute
the
change
in
OSCi
The other factor affecting accuracy is large jitter on
the reference input prior
mode switch. For instance, jitter of 7.5UI at 700Hz
may reduce the Holdover Mode accuracy from
0.05ppm to 0.10ppm.
(30ms to 60ms) to the
Freerun Mode
Freerun Mode is typically used when a master clock
source is required, or immediately following system
power-up
before
network
achieved.
synchronization
is
In Freerun Mode, the MT9042C provides timing and
synchronization signals which are based on the
master clock frequency (OSCi) only, and are not
synchronized to the reference signals (PRI and
SEC).
The accuracy of the output clock is equal to the
accuracy of the master clock (OSCi). So if a
±
32ppm
output clock is required, the master clock must also
be
±
32ppm.
See Applications - Crystal and Clock
Oscillator sections.
相關PDF資料
PDF描述
MT9043 T1/E1 System Synchronizer(T1/E1 系統同步裝置（由一個數字鎖相環組成）)
MT9044 T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）)
MT90500 Multi-Channel ATM AAL1 SAR(多通道 ATM AAL1分段及重組設備（基于通訊總線的系統與ATM網絡的接口）)
MT90500 Multi-Channel ATM AAL1 SAR
MT90500AL Multi-Channel ATM AAL1 SAR
相關代理商/技術參數
參數描述
MT9042CP 制造商:Microsemi Corporation 功能描述: 制造商:Mitel Networks Corporation 功能描述:
MT9042CP1 制造商:Microsemi Corporation 功能描述:SYNCHRONIZER 28PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE MULTITRUNK SYSTEM SYNCHRONIZER 制造商:Zarlink Semiconductor Inc 功能描述:SYNCHRONIZER 28PLCC - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE MULTITRUNK SYSTEM SYNCHRONIZER
MT9042CPR1 制造商:Microsemi Corporation 功能描述:SYNCHRONIZER 28PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:SYNCHRONIZER 28PLCC - Tape and Reel
MT9043 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 System Synchronizer
MT9043AN 制造商:Microsemi Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*