- 您現在的位置：買賣IC網 > PDF目錄359233 > MT8931C (Mitel Networks Corporation) CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information PDF資料下載
參數資料
| 型號： | MT8931C |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| 中文描述： | 意法半導體的CMOS總線⑩家庭用戶網絡接口電路的初步信息 |
| 文件頁數： | 23/39頁 |
| 文件大?。?/td> | 833K |
| 代理商： | MT8931C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Data Sheet
MT8931C
23
Table 16. TE Mode C-channel Control Register
(2)
(Write Add. 01000
B
and B0 = 0)
Note 1:
Note 2:
Allow one ST-BUS frame to input the C-channel and one ST-BUS frame to establish the connection.
The C-channel Control Register is updated once every ST-BUS frame. Therefore, this register should not be written to
more than once per frame, otherwise, the last access will override previous ones.
Table 17. TE Mode Diagnostic Register (Write Add. 01000
B
and B0 = 1)
BIT
NAME
DESCRIPTION
B7
AR
Setting this bit will initiate the activation of the S-Bus.
If ’0’, the device will remain in the present state.
B6
DR
Setting this bit will initiate the deactivation of the S-Bus.
If ’0’, the device will remain in the present state. This bit has priority over AR.
B5
DinB
If ’1’, the D-channel will be placed in the B1 timeslot allocating 64 kbit/s to the
D-channel.
(1)
If ’0’, the D-channel will assume its position with a 16 kbit/s bandwidth.
(1)
B4
Priority
The status of this bit selects the priority class of the terminal equipment. A ’1’ selects the
high priority and a ’0’ selects the low priority.
B3
DReq
This bit is used to request or relinquish the D-channel on the S-Bus when the D-channel
source is the ST-BUS. A ’1’ will request the D-channel, a ’0’ will relinquish it.
Keep at ’0’ when the D-channel source is the HDLC transmitter.
B2
TxMCH
The state of this bit will be transmitted in the maintenance channel (Q-channel).
B1
ClrDia
A ’1’ will clear the contents of the Diagnostics Register.
A ’0’ will enable the maintenance functions found in the Diagnostic Register.
This bit should be set to 1 as long as the device is not fully active (IS0, IS1
≠
1,1).
B0
RegSel
If the register select bit is set to ’1’, the control register is redefined as the diagnostic
Register. A ’0’ gives access to the Control Register.
BIT
NAME
DESCRIPTION
B7-B6
Loop
The status of these two bits determine which type of loopback is to be performed:
B7 - B6
0 - 0
- no loopback active
0 - 1
- near end loopback LTx to LRx
1 - 0
- digital loopback DSTi to DSTo
1 - 1
- remote loopback LRx to LTx
B5
FSync
If ’1’, the device will maintain frame synchronization even after losing the frame sync
sequence (i.e., if the device is transmitting INFO3 and this bit is set, INFO3 will still be
transmitted even if the frame sync sequence in the received signal is lost).
If ’0’, synchronization will be declared when three consecutive framing sequences have
been detected.
B4
FLv
If ’1’, the frame sync sequence will violate the normal bipolar encoding rule.
If ’0’, the framing pattern resumes normal operation, i.e., framing bit will be a bipolar
violation.
B3
Idle
If ’1’, an all 1s signal is transmitted on the line.
If ’0’, the transmitter will resume normal operation.
B2-B1
NA
Unused.
B0
RegSel
If the register select bit is set to ’1’, the control register is redefined as the diagnostic
register. A ’0’ gives access to the control register.
相關PDF資料 |
PDF描述 |
|---|---|
| MT8931CC | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8931CP | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| MT8941 | Advanced T1/CEPT Digital Trunk PLL |
| MT8941BE | Advanced T1/CEPT Digital Trunk PLL |
| MT8941BP | Advanced T1/CEPT Digital Trunk PLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8931C-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| MT8931CC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8931CE | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8931CP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8940 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY T1/CEPT Digital Trunk PLL |
發布緊急采購，3分鐘左右您將得到回復。