- 您現在的位置：買賣IC網 > PDF目錄384758 > MT88E46 (Mitel Networks Corporation) Bellcore Compliant Calling Number Identification Circuit(兼容貝爾內核主叫識別電路) PDF資料下載
參數資料
| 型號： | MT88E46 |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Bellcore Compliant Calling Number Identification Circuit(兼容貝爾內核主叫識別電路) |
| 中文描述： | 貝爾通訊兼容主叫號碼識別電路（兼容貝爾內核主叫識別電路） |
| 文件頁數： | 3/25頁 |
| 文件大?。?/td> | 111K |
| 代理商： | MT88E46 |
3
Advance Information
MT88E46
10
DATA
3-Wire FSK Interface Data (CMOS Logic Output).
Mark frequency corresponds to logical 1.
Space frequency corresponds to logical 0.
In interface mode 0 (when the CB0 pin is logic low) the FSK serial bit stream is output to DATA
directly.
In interface mode 1 (when the CB0 pin is logic high) the start bit is stripped off, the data byte
and the trailing stop bit are stored in a 9 bit buffer. At the end of each word indicated by the DR
signal at the DR/DET pin, the microcontroller should shift the byte out to DATA by applying 8
read pulses to the DCLK pin. A 9th DCLK pulse will shift out the trailing stop bit for framing
error checking.
11
DR/DET
3-Wire FSK Interface Data Ready/CAS Detect (CMOS Logic Output).
Active low.
This is a dual purpose pin which indicates the end of an FSK word or the end of CAS.
Data Ready:
When FSK demodulation is enabled this pin denotes the end of a word. In both
FSK interface modes 0 and 1, it is normally high and goes low for half a bit time at the end of a
word. In mode 1 if DCLK starts while DR is low, the first rising edge of the DCLK input will
return DR to high. This feature allows an interrupt requested by a low going DR to be cleared
upon reading the first DATA bit.
CAS Detect:
When CAS detection is enabled, this pin goes low after the end of CAS for 416
μ
s
(nominal) to indicate that CAS has been detected.
12
IC
Internal Connection.
Must be left open circuit.
13
NC
No Connection.
This pin is not bonded to the die and is unaffected by external connections.
14
CD
Carrier Detect (CMOS Logic Output).
Active low.
A logic low indicates that an FSK signal is present. A 10ms time hysteresis has been provided
to allow for momentary signal discontinuity. The demodulated FSK data is ignored until carrier
detect has been activated.
15
Vdd
Positive Power Supply.
A decoupling capacitor should be connected directly across the Vdd
and Vss pins.
16
CB1
Control Bit 1 (CMOS Logic Input).
Together with CB2 this pin enables FSK demodulation or
CAS detection. See Tables 1 and 2.
17
CB2
Control Bit 2 (CMOS Logic Input).
Together with CB1 this pin enables FSK demodulation or
CAS detection. See Tables 1 and 2.
18
GS2
Gain Select 2 (Output).
This is the output of the GS2 op-amp. The op-amp should be used to
connect the MT88E46 to the receive pair of the telephone hybrid or speech IC. The signal can
be amplified or attenuated at GS2 via selection of the feedback resistor between GS2 and IN2-
.
When the application is a telephone adjunct box where there is no hybrid or speech IC, if the
GS2 gain with respect to Tip/Ring is to be set to the same as that of GS1, the GS2 op-amp can
be connected as a voltage follower to the GS1 op-amp output (see Figure 5).
The GS2 signal is used for ‘off hook mode’ CAS detection only as selected via the CB1 and
CB2 pins. See Tables 1 and 2.
19
IN2-
GS2 Op-Amp Inverting Input.
The op-amp is for connecting the MT88E46 to the receive pair
of the telephone hybrid or speech IC.
20
IN2+
GS2 Op-Amp Non-Inverting Input.
The op-amp is for connecting the MT88E46 to the receive
pair of the telephone hybrid or speech IC.
Pin Description
Pin #
Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| MT88L70 | 3 Volt Integrated DTMF Receiver(3V 集成雙音多頻信號（DTMF）接收器) |
| MT88L85 | 3V Integrated DTMF Transceiver with Power-Down and Adaptive Micro Interface(3V 集成雙音多頻信號（DTMF）接收器（帶電源關閉和自適應微接口）) |
| MT88L89 | 3V Integrated DTMF Transceiver with Adaptive Micro Interface(3V 集成雙音多頻信號（DTMF）接收器（帶自適應微接口）) |
| MT88V32 | 8 x 4 High Performance Video Switch Array(8 x 4 高性能數字可編程正交開關（用于控制寬帶視頻信號）) |
| MT8910-1 | CMOS ST-BUS⑩ FAMILY Digital Subscriber Line Interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT88E46_06 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Bellcore Compliant Calling Number Identification Circuit |
| MT88E46AS | 制造商:Microsemi Corporation 功能描述:CALLER ID CMOS 3.58MHZ 3.3V/5V 20SOIC - Rail/Tube |
| MT88E46AS1 | 制造商:Microsemi Corporation 功能描述:CALLER ID CMOS 3.58MHZ 3.3V/5V 20SOIC - Rail/Tube |
| MT88E46ASR | 制造商:Microsemi Corporation 功能描述:CALLER ID CMOS 3.58MHZ 3.3V/5V 20SOIC - Tape and Reel |
| MT88E46ASR1 | 制造商:Microsemi Corporation 功能描述:CALLER ID CMOS 3.58MHZ 3.3V/5V 20SOIC - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。