- 您現在的位置：買賣IC網 > PDF目錄378018 > MSM82C51A-2GS (OKI SEMICONDUCTOR CO., LTD.) UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER PDF資料下載
參數資料
| 型號： | MSM82C51A-2GS |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER |
| 中文描述： | 通用同步異步收發器 |
| 文件頁數： | 10/26頁 |
| 文件大小： | 203K |
| 代理商： | MSM82C51A-2GS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
10/26
Semiconductor
MSM82C51A-2RS/GS/JS
TXRDY (output terminal)
This is an output terminal which indicates that the MSM82C51A-2 is ready to accept a
transmitted data character. But the terminal is always at low level if
CTS
= high or the device
was set in “TX disable status” by a command.
Note:
TXRDY status word indicates that transmit data character is receivable,
regardless
of
CTS
or command.
If the CPU writes a data character, TXRDY will be reset by the leading edge or
WR
signal.
TXEMPTY (Output terminal)
This is an output terminal which indicates that the MSM82C51A-2 has transmitted all the
characters and had no data character.
In “synchronous mode,” the terminal is at high level, if transmit data characters are no longer
remaining and sync characters are automatically transmitted. If the CPU writes a data
character, TXEMPTY will be reset by the leading edge of
WR
signal.
Note : As the transmitter is disabled by setting
CTS
“High” or command, data written
before disable will be sent out. Then TXD and TXEMPTY will be “High”.
Even if a data is written after disable, that data is not sent out and TXE will be
“High”.After
the transmitter is enabled, it sent out. (Refer to Timing Chart of
Transmitter Control and Flag
Timing)
TXC
(Input terminal)
This is a clock input signal which determines the transfer speed of transmitted data.
In “synchronous mode,” the baud rate will be the same as the frequency of
TXC
.
In “asynchronous mode”, it is possible to select the baud rate factor by mode instruction.
It can be 1, 1/16 or 1/64 the
TXC
.
The falling edge of
TXC
sifts the serial data out of the MSM82C51A-2.
RXD (input terminal)
This is a terminal which receives serial data.
RXRDY (Output terminal)
This is a terminal which indicates that the MSM82C51A-2 contains a character that is ready to
READ.
If the CPU reads a data character, RXRDY will be reset by the leading edge of
RD
signal.
Unless the CPU reads a data character before the next one is received completely, the preceding
data will be lost. In such a case, an overrun error flag status word will be set.
RXC
(Input terminal)
This is a clock input signal which determines the transfer speed of received data.
In “synchronous mode,” the baud rate is the same as the frequency of
RXC
.
In “asynchronous mode,” it is possible to select the baud rate factor by mode instruction.
It can be 1, 1/16, 1/64 the
RXC
.
相關PDF資料 |
PDF描述 |
|---|---|
| MSM82C51A-2JS | UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER |
| MSM82C51A-2RS | UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER |
| MSM82C59A-2GS | PROGRAMMABLE INTERRUPT CONTROLLER |
| MSM82C59A-2JS | PROGRAMMABLE INTERRUPT CONTROLLER |
| MSM82C59A-2RS | PROGRAMMABLE INTERRUPT CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM82C51A-2GS-K | 制造商:OK International 功能描述:USART, 32 Pin, Plastic, SOP 制造商:OKI Semiconductor 功能描述:USART, 32 Pin, Plastic, SOP |
| MSM82C51A-2JS | 制造商:ROHM Semiconductor 功能描述: |
| MSM82C51A-2RS | 制造商:ROHM Semiconductor 功能描述: 制造商:ROHM Semiconductor 功能描述:USART,Programmable multifunction 制造商:ROHM Semiconductor 功能描述:USART, programmable multi-function communication interface |
| MSM82C53-2 GS-K | 制造商:ROHM Semiconductor 功能描述: |
| MSM82C53-2GS | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:CMOS PROGRAMMABLE INTERVAL TIMER |
發布緊急采購，3分鐘左右您將得到回復。