- 您現在的位置：買賣IC網 > PDF目錄378678 > MSM6679A-110 (OKI SEMICONDUCTOR CO., LTD.) Voice Synthesiser(SI/SD話音識別,記錄/播放,語音合成器) PDF資料下載
參數資料
| 型號： | MSM6679A-110 |
| 廠商： | OKI SEMICONDUCTOR CO., LTD. |
| 英文描述： | Voice Synthesiser(SI/SD話音識別,記錄/播放,語音合成器) |
| 中文描述： | 語音合成器（硅/標清話音識別，記錄/播放，語音合成器） |
| 文件頁數： | 35/50頁 |
| 文件大小： | 362K |
| 代理商： | MSM6679A-110 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Semiconductor
MSM6679A-110 Voice Recognition Processor
33
Initialize
F2xx Bit
Values
After power-on, the MSM6679A-110's mode corresponds to that after issuing a F20C command.
This mode may NOT be the optimum condition for most situations, so the user is advised to carefully understand
the desired condition and develop a suitable command for the application at hand.
In addition, ensure that unwanted bits do not get set or reset when attempting to set individual conditions. The
conditions selected are based on the XXh values associated with the last F2 command issued.
Background Noise Initialization. When set to 1, the MSM6679A-
110 starts a 500-ms background noise initialization. When set to
0, the MSM6679A-110 does not perform background noise
initialization.
The MSM6679A-110 requires this command prior to recognition
for noise vector subtraction during the utterance sampling period.
Use the background initialization command whenever there is a
change in the background noise level. For example, sample the
noise signature in a vehicle at rest and moving at 35 MPH with its
windows rolled down. The quality of a phone line connection can
also vary from call to call.
The host MCU must implement a strategy as to when to issue a
background initialization command. In a vehicle, the host MCU
could monitor the vehicle speed, fan speed, radio volume, etc.
Alternatively, the host MCU could issue this command each time a
new recognition session starts or a new line connection is
established. However, the 0.5-sec sample period could degrade
system responsiveness if used too frequently. A zero in this bit
location during the F2XXh command will not cause an
initialization. The F505h command causes the same initialization
sequence.
Wait for Recognition Command/Auto Restart SI Recognition.
When set to 1, the MSM6679A-110 waits for a recognition
command after each response. When set to 0, the MSM6679A-
110 auto-restarts SI recogni-tion after each response.
This bit should be set to 1 when an action is to be taken
immediately after an utterance. Auto-restart recognition is the
desired mode during digit string recognition, automated tape
testing of digits, or in demonstrations where continuous
recognition is desired.
Power-On/
Reset Value
Action
Return Value
1xxx xxxx
Cleared
F501 = Background
initialization
complete
F2XY = Initialization
acknowledge.
[1]
x1xx xxxx
Cleared
F2XY = Initialization
acknowledge.
[1]
相關PDF資料 |
PDF描述 |
|---|---|
| MSM7524 | DTMF Transceiver(雙音多頻收發器) |
| MSM7547 | Voice Signal Level Control LSI(音頻信號電平控制LSI) |
| MSM80C86A-10 | 16-Bit CMOS Microprocessor(全靜態設計,最高工作頻率10MHz,數據、地址復用,16位微處理器) |
| MSM80C88A-10 | 8-Bit CMOS Microprocessor(內部結構為16位,外圍接口8位,8位微處理器) |
| MSM82C37B-5RS | Programmable DMA Controller(可編程DMA控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSM6679AL-110 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:SI/SD Voice Recognizer, Recorder/Player, and Speech Synthesizer |
| MSM6684B | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:4,194,304-word x 1-bit Serial Register |
| MSM6685 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:8,388,608-Word x 1-Bit Serial Register |
| MSM6685A | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:8,388,608-Word x 1-Bit Serial Register |
| MSM6685AJS | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:8,388,608-Word x 1-Bit Serial Register |
發布緊急采購，3分鐘左右您將得到回復。