參數資料
型號: MS80C51-12D
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 36/80頁
文件大小: 5152K
代理商: MS80C51-12D
227
2466T–AVR–07/10
ATmega16(L)
On-chip Debug
Related Register in
I/O Memory
On-chip Debug
Register – OCDR
The OCDR Register provides a communication channel from the running program in the micro-
controller to the debugger. The CPU can transfer a byte to the debugger by writing to this
location. At the same time, an Internal Flag; I/O Debug Register Dirty – IDRD – is set to indicate
to the debugger that the register has been written. When the CPU reads the OCDR Register the
7 LSB will be from the OCDR Register, while the MSB is the IDRD bit. The debugger clears the
IDRD bit when it has read the information.
In some AVR devices, this register is shared with a standard I/O location. In this case, the OCDR
Register can only be accessed if the OCDEN Fuse is programmed, and the debugger enables
access to the OCDR Register. In all other cases, the standard I/O location is accessed.
Refer to the debugger documentation for further information on how to use this register.
Using the JTAG
Programming
Capabilities
Programming of AVR parts via JTAG is performed via the 4-pin JTAG port, TCK, TMS, TDI and
TDO. These are the only pins that need to be controlled/observed to perform JTAG program-
ming (in addition to power pins). It is not required to apply 12V externally. The JTAGEN Fuse
must be programmed and the JTD bit in the MCUSR Register must be cleared to enable the
JTAG Test Access Port.
The JTAG programming capability supports:
Flash programming and verifying
EEPROM programming and verifying
Fuse programming and verifying
Lock bit programming and verifying
The Lock bit security is exactly as in Parallel Programming mode. If the Lock bits LB1 or LB2 are
programmed, the OCDEN Fuse cannot be programmed unless first doing a chip erase. This is a
security feature that ensures no back-door exists for reading out the content of a secured
device.
The details on programming through the JTAG interface and programming specific JTAG
instructions are given in the section “Programming via the JTAG Interface” on page 278.
Bibliography
For more information about general Boundary-scan, the following literature can be consulted:
IEEE: IEEE Std. 1149.1-1990. IEEE Standard Test Access Port and Boundary-scan
Architecture, IEEE, 1993
Colin Maunder: The Board Designers Guide to Testable Logic Circuits, Addison-Wesley,
1992
Bit
7
6
543210
MSB/IDRD
LSB
OCDR
Read/Write
R/W
Initial Value
0
000000
相關PDF資料
PDF描述
MT80C51T-16R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
MD80C32E-20SC 8-BIT, 20 MHz, MICROCONTROLLER, CDIP40
MC80C52XXX-16SHXXX 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40
MD80C52EXXX-20 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40
MR80C52CXXX-12SHXXX 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
MS8100 制造商:MCC 制造商全稱:Micro Commercial Components 功能描述:8 Amp Schottky Barrier Rectifier 20 to 100 Volts
MS8100.D 制造商:Colibrys SA 功能描述:MEMS CAPACITIVE ACCELEROMETERS - Trays
MS8104160 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:(262,214-word x 8-Bits) x 2 Dual FIFO
MS8104160A 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:Dual FIFO (262,214 Words 】 8 Bits) 】 2
MS8104160A-XXTB 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:Dual FIFO (262,214 Words 】 8 Bits) 】 2