參數資料
型號: MPC9893AE
廠商: IDT, Integrated Device Technology Inc
文件頁數: 13/14頁
文件大?。?/td> 0K
描述: IC PLL CLK GEN 1:12 3.3V 48-LQFP
標準包裝: 250
類型: PLL 時鐘發生器
PLL: 帶旁路
輸入: LVCMOS
輸出: LVCMOS
電路數: 1
比率 - 輸入:輸出: 2:12
差分 - 輸入:輸出: 無/無
頻率 - 最大: 200MHz
除法器/乘法器: 是/是
電源電壓: 2.375 V ~ 3.465 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-LQFP
供應商設備封裝: 48-TQFP(7x7)
包裝: 托盤
MPC9893 REVISION 8 JANUARY 16, 2013
8
2013 Integrated Device Technology, Inc.
MPC9893 Data Sheet
3.3V 1:12 LVCMOS PLL CLOCK GENERATOR
Figure 3. VCC_PLL Power Supply Filter
The minimum values for RF and the filter capacitor CF are
defined by the required filter characteristics: the RC filter
should provide an attenuation greater than 40 dB for noise
whose spectral content is above 100 kHz. In the example RC
filter shown in Figure 3, the filter cut-off frequency is around
3-5 kHz and the noise attenuation at 100 kHz is better than
42 dB.
As the noise frequency crosses the series resonant point
of an individual capacitor its overall impedance begins to look
inductive and thus increases with increasing frequency. The
parallel capacitor combination shown ensures that a low
impedance path to ground exists for frequencies well above
the bandwidth of the PLL. Although the MPC9893 has
several design features to minimize the susceptibility to
power supply noise (isolated power and grounds and fully
differential PLL) there still may be applications in which
overall performance is being degraded due to system power
supply noise. The power supply filter schemes discussed in
this section should be adequate to eliminate power supply
noise related problems in most designs.
Using the MPC9893 in Zero-Delay Applications
Nested clock trees are typical applications for the
MPC9893. Designs using the MPC9893 as LVCMOS PLL
fanout buffer with zero insertion delay will show significantly
lower clock skew than clock distributions developed from
CMOS fanout buffers. The external feedback option of the
MPC9893 clock driver allows for its use as a zero delay
buffer. The the propagation delay through the device is
virtually eliminated. The PLL aligns the feedback clock output
edge with the clock input reference edge resulting a near zero
delay through the device. The maximum insertion delay of the
device in zero-delay applications is measured between the
reference clock input and any output. This effective delay
consists of the static phase offset, I/O jitter (phase or long-
term jitter), feedback path delay and the output-to-output
skew error relative to the feedback output.
Calculation of Part-to-Part Skew
The MPC9893 zero delay buffer supports applications
where critical clock signal timing can be maintained across
several devices. If the reference clock inputs of two or more
MPC9893 are connected together, the maximum overall
timing uncertainty from the common CLK0 or CLK1 input to
any output is:
tSK(PP) = t() + tSK(O) + tPD, LINE(FB) + tJIT() CF
This maximum timing uncertainty consist of four
components: static phase offset, output skew, feedback
board trace delay and I/O (phase) jitter:
Figure 4. MPC9893 Max. Device-to-Device Skew
Due to the statistical nature of I/O jitter a RMS value (1
)
is specified. I/O jitter numbers for other confidence factors
(CF) can be derived from Table 9.
The feedback trace delay is determined by the board
layout and can be used to fine-tune the effective delay
through each device. In the following example calculation a I/
O jitter confidence factor of 99.7% (
3) is assumed,
resulting in a worst case timing uncertainty from the common
clock input to any MPC9893 output of –275 ps to +265 ps
relative to the reference clock input CLK0/1:
tSK(PP) = [–60ps...50ps] + [-125ps...125ps] +
[(30ps
–3)...(30ps 3)] + tPD, LINE(FB)
tSK(PP) = [–275ps...265ps] + tPD, LINE(FB)
Example configuration:
fref = 100 MHz, VCC = 3.3 V
fVCO = 400 MHz, FSEL[0:2]=111
VCC_PLL
VCC
MPC9893
10 nF
RF = 5–15
CF = 22F
CF
33...100 nF
RF
VCC
Table 9. Confidence Factor CF
CF
Probability of clock edge within the distribution
1
0.68268948
2
0.95449988
3
0.99730007
4
0.99993663
5
0.99999943
6
0.99999999
tPD,LINE(FB)
tJIT()
+tSK(O)
—t()
+t()
tJIT()
+tSK(O)
tSK(PP)
Max. skew
TCLKCommon
QFBDevice 1
Any QDevice 1
QFBDevice2
Any QDevice 2
相關PDF資料
PDF描述
MSTM-S3-TR-19.44M IC MOD TIMING 19.440MHZ STRAT 3
MT5656RJ-92.R2 MODEM SERIAL DATA V.92 5V
MT5656SMI-IP-92-SP MODEM EMBEDDED SERIAL V.92 5V
MT9234SMI-P-HV-92-SP MODEM V.92 PAR DATA V.34 FAX 5V
MX7224KCWN+ IC DAC 8BIT CMOS PREC AMP 18SOIC
相關代理商/技術參數
參數描述
MPC9893AER2 功能描述:時鐘發生器及支持產品 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MPC9893FA 功能描述:時鐘發生器及支持產品 2.5 3.3V 200MHz Clock Generator RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MPC9893FAR2 制造商:Integrated Device Technology Inc 功能描述:PLL Clock Driver Single 48-Pin LQFP T/R 制造商:Integrated Device Technology Inc 功能描述:MPC9893FAR2 - Tape and Reel
MPC9894 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Quad Input Redundant IDCS Clock Generator
MPC9894VM 制造商:IDT from Components Direct 功能描述:IDT MPC9894VM PLL - Trays 制造商:IDT 功能描述:IDT MPC9894VM PLL