參數資料
型號： MPC8313ECZQADDB
廠商： Freescale Semiconductor
文件頁數： 90/99頁
文件大?。?/td> 0K
描述： MPU POWERQUICC II PRO 516-PBGA
標準包裝： 40
系列： MPC83xx
處理器類型： 32-位 MPC83xx PowerQUICC II Pro
速度： 267MHz
電壓： 0.95 V ~ 1.05 V
安裝類型： 表面貼裝
封裝/外殼： 516-BBGA 裸露焊盤
供應商設備封裝： 516-PBGAPGE（27x27）
包裝： 托盤
MPC8313E PowerQUICC II Pro Processor Hardware Specifications, Rev. 4
90
Freescale Semiconductor
Third, between the device and any SerDes voltage regulator there should be a 10-F, low
equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT
tantalum chip capacitor. This should be done for all SerDes supplies.
22.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active low inputs should be tied to NVDD, GVDD, LVDD, LVDDA, or LVDDB as required.
Unused active high inputs should be connected to VSS. All NC (no-connect) signals must remain
unconnected.
Power and ground connections must be made to all external VDD, NVDD, GVDD, LVDD, LVDDA, LVDDB,
and VSS pins of the device.
22.6
Output Buffer DC Impedance
The MPC8313E drivers are characterized over process, voltage, and temperature. For all buses, the driver
is a push-pull single-ended driver type (open drain for I2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to NVDD
or VSS. Then, the value of each resistor is varied until the pad voltage is NVDD/2 (see Figure 60). The
output impedance is the average of two components, the resistances of the pull-up and pull-down devices.
When data is held high, SW1 is closed (SW2 is open), and RP is trimmed until the voltage at the pad equals
NVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each
other in value. Then, Z0 = (RP + RN)/2.
Figure 60. Driver Impedance Measurement
The value of this resistance and the strength of the driver’s current source can be found by making two
measurements. First, the output voltage is measured while driving logic 1 without an external differential
termination resistor. The measured voltage is V1 = Rsource Isource. Second, the output voltage is measured
while driving logic 1 with an external precision differential termination resistor of value Rterm. The
measured voltage is V2 =(1/(1/R1 +1/R2)) Isource. Solving for the output impedance gives Rsource =
Rterm (V1/V2 – 1). The drive current is then Isource =V1/Rsource.
NVDD
VSS
Pad
Data
SW1
SW2
RN
RP
相關PDF資料
PDF描述
IDT71V65803S133BGI IC SRAM 9MBIT 133MHZ 119BGA
MPC8313ECVRADDB MPU POWERQUICC II PRO 516-PBGA
FMC36DRYN-S13 CONN EDGECARD 72POS .100 EXTEND
IDT71V65803S133BGGI IC SRAM 9MBIT 133MHZ 119BGA
M68LC302CAF16VCT IC MPU MULTI PROTOCOL 100-LQFP
相關代理商/技術參數
參數描述
MPC8313ECZQADDC 功能描述:微處理器 - MPU 8313 REV2.2 PB ENC EXT RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC8313ECZQAFD 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8313ECZQAFDA 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8313ECZQAFDB 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:PowerQUICC? II Pro Processor Hardware Specifications
MPC8313ECZQAFF 功能描述:微處理器 - MPU 8313 PB PBGA W/ ENCR RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*