- 您現在的位置：買賣IC網 > PDF目錄45354 > MPC8245LVV333D (MOTOROLA INC) 32-BIT, 333 MHz, RISC PROCESSOR, PBGA352 PDF資料下載
參數資料
| 型號： | MPC8245LVV333D |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, 333 MHz, RISC PROCESSOR, PBGA352 |
| 封裝： | 35 X 35 MM, 1.27 MM PITCH, LEAD FREE, TBGA-352 |
| 文件頁數： | 41/64頁 |
| 文件大?。?/td> | 893K |
| 代理商： | MPC8245LVV333D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
46
MPC8245 Integrated Processor Hardware Specifications
MOTOROLA
System Design Information
1.7.3
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. Unused active-low inputs should be tied to OVDD. Unused active-high inputs should be connected to
GND. All NC signals must remain unconnected.
Power and ground connections must be made to all external VDD, OVDD, GVDD, LVDD, and GND pins of
the MPC8245.
The PCI_SYNC_OUT signal is intended to be routed halfway out to the PCI devices and returned to the
PCI_SYNC_IN input of the MPC8245.
The SDRAM_SYNC_OUT signal is intended to be routed halfway out to the SDRAM devices and then
returned to the SDRAM_SYNC_IN input of the MPC8245. The trace length may be used to skew or adjust
the timing window as needed. See the Motorola application notes AN1849, the Tundra Tsi107 Design
Guide, and AN2164, MPC8245/MPC8241 Memory Clock Design Guidelines, for more information on this
topic. Note that there is an SDRAM_SYNC_IN to PCI_SYNC_IN time requirement (refer to Table 10 for
the input AC timing specifications).
1.7.4
Pull-Up/Pull-Down Resistor Requirements
The data bus input receivers are normally turned off when no read operation is in progress; therefore, they
do not require pull-up resistors on the bus. The data bus signals are: MDH[0:31], MDL[0:31], and PAR[0:7].
If the 32-bit data bus mode is selected, the input receivers of the unused data and parity bits (MDL[0:31]
and PAR[4:7]) will be disabled, and their outputs will drive logic zeros when they would otherwise normally
be driven. For this mode, these pins do not require pull-up resistors and should be left unconnected by the
system to minimize possible output switching.
The TEST0 pin requires a pull-up resistor of 120
or less connected to OV
DD.
It is recommended that RTC have weak pull-up resistors (2–10 k
) connected to GV
DD.
It is recommended that the following signals be pulled up to OVDD with weak pull-up resistors (2–10 k):
SDA, SCL, SMI, SRESET/SDMA12, TBEN/SDMA13, CHKSTOP_IN/SDMA14, TRIG_IN/RCS2,
INTA, QACK/DA0 and DRDY. Note that QACK/DA0 should be left without a pull-up resistor only if an
external clock is used because this signal enables internal clock flipping logic when it is low on reset, which
is necessary when the PLL[0:4] signals select a half-clock frequency ratio and an external PLL is used to
drive the SDRAM device.
It is recommended that the following PCI control signals be pulled up to LVDD (the clamping voltage) with
weak pull-up resistors (2–10 k
): DEVSEL, FRAME, IRDY, LOCK, PERR, SERR, STOP, and TRDY. The
resistor values may need to be adjusted stronger to reduce induced noise on specific board designs.
The following pins have internal pull-up resistors enabled at all times: REQ[3:0], REQ4/DA4, TCK, TDI,
TMS, and TRST. See Table 17 for more information.
The following pins have internal pull-up resistors enabled only while device is in the reset state:
GNT4/DA5, MDL0, FOE, RCS0, SDRAS, SDCAS, CKE, AS, MCP, MAA[0:2], and PMAA[0:2]. See
Table 17 for more information on the MPC8245 pins.
The following pins are reset configuration pins: GNT4/DA5, MDL[0], FOE, RCS0, CKE, AS, MCP,
QACK/DA0, MAA[0:2], PMAA[0:2], SDMA[1:0], MDH[16:31], and PLL_CFG[0:4]/DA[10:15]. These
pins are sampled during reset to configure the device. The PLL_CFG[0:4] signals are sampled a few clocks
after the negation of HRST_CPU and HRST_CTRL.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC8245LVV350D | 32-BIT, 350 MHz, RISC PROCESSOR, PBGA352 |
| MPC8245LZU266D | 32-BIT, 266 MHz, RISC PROCESSOR, PBGA352 |
| MPC8245LVV300D | 32-BIT, 300 MHz, RISC PROCESSOR, PBGA352 |
| MPC8245LVV333D | 32-BIT, 333 MHz, RISC PROCESSOR, PBGA352 |
| MPC8245TVV300D | 32-BIT, 300 MHz, RISC PROCESSOR, PBGA352 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC8245LVV350D | 功能描述:微處理器 - MPU INTEGRATED HOST PROC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8245LZU266D | 功能描述:微處理器 - MPU 266MHz 505.4MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8245LZU300D | 功能描述:微處理器 - MPU 300MHz 570MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8245LZU333D | 功能描述:微處理器 - MPU 333MHz 632.7MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC8245LZU350D | 功能描述:微處理器 - MPU 350MHz 665MIPS RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。