Revision History for the MPC5553 Data Sheet
MPC5553 Microcontroller Data Sheet, Rev. 3.0
Freescale Semiconductor
63
Table 7 Power Sequence Pin Status for Fast Pads
Changed title to Pin Status for Fast Pads During the Power Sequence
Changed preceding paragraph
From:
Although there are no power up/down sequencing requirements to prevent issues like latch-up, excessive current
spikes, etc., the state of the I/O pins during power up/down varies depending on power. Prior to exiting POR, the
pads are in a high impedance state (Hi-Z).
To:
There are no power up/down sequencing requirements to prevent issues such as latch-up, excessive current
spikes, and so on. Therefore, the state of the I/O pins during power up/down varies depending on which supplies
are powered.
Table 8 Power Sequence Pin Status for Medium/Slow Pads:
Changed title to Pin Status for Medium and Slow Pads During the Power Sequence
Updated preceding paragraph.
Table 9 DC Electrical Specifications:
Spelled the slash ‘/’ as ‘a(chǎn)nd’ as well as ‘I/O’ as ‘input/output.’ Still very confusing. Deleted ‘input/output’.
Added footnote that reads: VDDE2 and VDDE3 are limited to 2.25–3.6 V only if EBTS = 0; VDDE2 and VDDE3 have
a range of 1.6–3.6 V if EBTS =1.
Spec 20, column 2, Characteristics,’ Slow and medium output high voltage (IOH_S = –2.0 mA):’
Created a left-justified second line and moved ‘IOH_S = –2.0 mA’ from the 1st line to the second line and deleted
the parentheses. Created a left-justified third line that reads ‘IOH_S = –1.0 mA.’
Spec 20, column 4, Min.: Added a blank line before and after ‘0.80
× V
DDEH’ and put ‘0.85 × VDDEH’ on the last
line.
Spec 22, column 2, ’Slow and medium output low voltage (IOL_S = 2.0 mA):’ Created a left-justified second line
and moved ‘IOL_S = 2.0 mA.’ from the 1st line to the second line and deleted the parentheses. Created a
left-justified third line that reads ‘IOL_S = 1.0 mA.’ Column 5, Max: Added a blank line before and after ‘0.20 ×
VDDEH’ and put ‘0.15 × VDDEH’ on the last line.
Spec 26: Changed ‘AN[12]_MA[1]_SDO’ to ‘AN[13]_MA[1]_SDO’.
Spec 27a: Operating current 1.5 V supplies @ 132 MHz changed to:
1.65 typical = 460
1.35 typical = 360
1.65 high = 510
1.35 high = 410
Spec 27b, Operating current 1.5 V supplies @ 114 MHz changed to:
1.65 typical = 410
1.35 typical = 310
1.65 high = 460
1.35 high = 370
Spec 27c, Operating current 1.5 V supplies @ 82 MHz changed to:
1.65 typical = 330
1.35 typical = 225
1.65 high = 385
1.35 high = 290
Spec 28: Changed 132 MHz to fMAX MHz.
Footnote 3 changed to read: If standby operation is not required, connect VSTBY to ground.
Footnote 6 is now:
Figure 3 shows an illustration of the IDD_STBY values interpolated for these temperature
values.
Deleted footnote 9: ‘Preliminary. Final specification pending characterization.’
Deleted duplicate footnote: ‘ Absolute value of current, measured at VIL and VIH.
Table 33. Table and Figure Changes Between Rev. 2.0 and 3.0 (continued)
Location
Description of Changes
Because
of
an
order
from
the
United
States
International
Trade
Commission,
BGA-packaged
product
lines
and
part
numbers
indicated
here
currently
are
not
available
from
Freescale
for
import
or
sale
in
the
United
States
prior
to
September
2010:
MPC551x
and
MPC5533
products
in
208
MAPBGA
packages;
MPC5534
and
MPC5553
products
in
208
and
496
MAPBGA
packages;
MPC5554,
MPC5565,
MPC5566
and
MPC5567
products
in
496
MAPBGA
packages