- 您現在的位置：買賣IC網 > PDF目錄69035 > MM908E625ACPEK (FREESCALE SEMICONDUCTOR INC) FLASH, 32 MHz, MICROCONTROLLER, PDSO54 PDF資料下載
參數資料
| 型號： | MM908E625ACPEK |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | FLASH, 32 MHz, MICROCONTROLLER, PDSO54 |
| 封裝： | 5.10 X 10.30 MM, 0.65 MM PITCH, LEAD FREE, SOIC-54 |
| 文件頁數： | 36/49頁 |
| 文件大?。?/td> | 965K |
| 代理商： | MM908E625ACPEK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
908E625
TYPICAL APPLICATIONS
FACTORY TRIMMING AND CALIBRATION
EMC/EMI RECOMMENDATIONS
This paragraph gives some device specific
recommendations to improve EMC/EMI performance.
Further generic design recommendations can be e.g. found
on the Freescale web site www.freescale.com.
VSUP pins (VSUP1:VSUP3)
Its recommended to place a high-quality ceramic
decoupling capacitor close to the VSUP pins to improve
EMC/EMI behavior.
LIN pin
For DPI (Direct Power Injection) and ESD (Electro Static
Discharge) its recommended to place a high quality ceramic
decoupling capacitor near the LIN pin. An additional varistor
will further increase the immunity against ESD. A ferrite in the
LIN line will suppress some of the noise induced.
Voltage regulator output pins (VDD and AGND)
Use a high quality ceramic decoupling capacitor to
stabilize the regulated voltage.
MCU digital supply pins (EVDD and EVSS)
Fast signal transitions on MCU pins place high, short-
duration current demands on the power supply. To prevent
noise problems, take special care to provide power supply
bypassing at the MCU. It is recommended that a high quality
ceramic decoupling capacitor be placed between these pins.
MCU analog supply pins (VREFH, VDDA and VREFL,
VSSA)
To avoid noise on the analog supply pins its important to
take special care on the layout. The MCU digital and analog
supplies should be tied to the same potential via separate
traces and connected to the voltage regulator output.
schematics and layout level and Table 13 indicates
recommended external components and layout
considerations.
Figure 25. EMC/EMI Recommendations
MM908E625
VREFL
VDDA
EVDD
VDD
EVSS
VSS
VSUP1
GND1
VSUP
+
VREFH
VSSA
VSUP2
LIN
C1
C2
D1
C3
C4
C5
L1
V1
VSUP3
GND2
相關PDF資料 |
PDF描述 |
|---|---|
| MM908E630CVFC | MICROCONTROLLER, QCC44 |
| MN101CP66DBF | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP84 |
| MN101CF66DBF | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP84 |
| MN101CF66DAL | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| MN101CP66DAL | 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。