- 您現在的位置：買賣IC網 > PDF目錄45333 > ML9040A-AXXWA (OKI ELECTRIC INDUSTRY CO LTD) 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC81 PDF資料下載
參數資料
| 型號： | ML9040A-AXXWA |
| 廠商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分類： | 顯示控制器 |
| 英文描述： | 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC81 |
| 封裝： | ALUMINUM PAD, DIE-81 |
| 文件頁數： | 27/49頁 |
| 文件大?。?/td> | 515K |
| 代理商： | ML9040A-AXXWA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
ML9040A-Axx/-Bxx
Semiconductor
33/49
PEDL9040A-03
Interface with LCD and MSM5259
Display examples when setting the 5 x 7 dots character font 1-line mode, 5 x 10 dots character font
1-line mode, and 5 x 7 dots character font 2-line mode through instructions are shown in Figures
4, 5, and 6, respectively.
When the 5 x 7 dots character font is set in the 1-line display mode, the COM signals COM9 to
COM16 are output for extinguishing.
Likewise, when the 5 x 10 dots character font (1-line is set), the COM signals COM12 to COM16
are output for display-off.
The display example shows a combination of 16 characters (32 characters for the 2-line display
mode) and the LCD. When the number of MSM5259s are increased according to the increase in
the number of characters, it is possible to display a maximum of 80 characters.
Besides, it is necessary to generate bias voltage required for LCD operation by splitting resistors
outside the IC to input it to ML9040A-Axx/-Bxx and MSM5259.
Examples of these bias voltages are shown in Figures 7, 8, 9, and 10. Basically, this can be done
by dividing the voltage by the resistors as shown in Figures 7 and 8. If the value of resistor R is
made larger to reduce system power consumption, the LCD operating margin decreases and the
LCD driving waveform is distorted. To prevent this, a by-pass capacitor is serially connected to
the resistor to lower voltage division impedance caused by the splitting of resistors as shown in
Figures 9 and 10.
As the values of R, VR, and C vary according to the LCD size used and VLCD (LCD drive voltage),
these values have to be determined through actual experimentation in combination with the
LCD.
(Example set values: R = 3.3 to 10kW, VR = 10 to 30kW, and C = 0.0022 mF to 0.047 mF)
Figure 17 shows an application circuit for the ML9040A-Axx/-Bxx and MSM5259 including a
bias circuit.
The bias voltage has to maintain the following potential relation:
VDD > V1 > V2 ≥ V3 > V4 > V5
Figure 4
In the case of 1-line 16 characters display (5 x 7 dots/font)
COM1
SEG1
SEG40
O1
O40
DO
CP
DF
L
DI1
CP
MSM5259
DF
LOAD
DO20 DI21
LCD
COM8
ML9040A-Axx/-Bxx
相關PDF資料 |
PDF描述 |
|---|---|
| ML9040A-BXXGA | 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP80 |
| ML9040A-AXXWA | 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC81 |
| ML9040A-BXXWA | 16 X 40 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC81 |
| ML9041A-01ACVWA | 17 X 100 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC189 |
| ML9041A-01ACVWA | 17 X 100 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC189 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML9040A-B01GAZ03A-7 | 功能描述:LCD 驅動器 LCD DOT Matrix Controller, 16/40 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| ML9040A-BXX | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 16-DOT COMMON DRIVER AND 40-DOT SEGMENT DRIVER |
| ML9040A-BXXGA | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 16-DOT COMMON DRIVER AND 40-DOT SEGMENT DRIVER |
| ML9040A-BXXWA | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 16-DOT COMMON DRIVER AND 40-DOT SEGMENT DRIVER |
| ML9040-AXX | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:DOT MATRIX LCD CONTROLLER WITH 16-DOT COMMON DRIVER AND 40-DOT SEGMENT DRIVER |
發布緊急采購，3分鐘左右您將得到回復。