- 您現在的位置：買賣IC網 > PDF目錄359170 > ML4826IP-1 PFC and Dual Output PWM Controller Combo PDF資料下載
參數資料
| 型號： | ML4826IP-1 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | PFC and Dual Output PWM Controller Combo |
| 中文描述： | PFC和雙輸出PWM控制器組合 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 296K |
| 代理商： | ML4826IP-1 |
ML4826
8
FUNCTIONAL DESCRIPTION
(Continued)
Figure 2. Compensation Network Connections for the
Voltage and Current Error Amplifiers
3) The output of the voltage error amplifier, VEAO. The
gain modulator responds linearly to variations in this
voltage.
The output of the gain modulator is a current signal, in the
form of a full wave rectified sinusoid at twice the line
frequency. This current is applied to the virtual-ground
(negative) input of the current error amplifier. In this way
the gain modulator forms the reference for the current
error loop, and ultimately controls the instantaneous
current draw of the PFC from the power line. The general
form for the output of the gain modulator is:
I
I
VEAO
2
V
V
GAINMOD
AC
RMS
×
×
1
More exactly, the output current of the gain modulator is
given by:
×
(
I
K
VEAO
V
I
GAINMOD
AC
)
×
– .5
(1)
where K is in units of V
-1
.
Note that the output current of the gain modulator is
limited to
200
μ
A.
Current Error Amplifier
The current error amplifier’s output controls the PFC duty
cycle to keep the current through the boost inductor a
linear function of the line voltage. At the inverting input to
the current error amplifier, the output current of the gain
modulator is summed with a current which results from a
negative voltage being impressed upon the I
SENSE
pin
(current into I
SENSE
V
SENSE
/3.5k
). The negative voltage
on I
SENSE
represents the sum of all currents flowing in the
PFC circuit, and is typically derived from a current sense
resistor in series with the negative terminal of the input
bridge rectifier. In higher power applications, two current
transformers are sometimes used, one to monitor the I
D
of
the boost MOSFET(s) and one to monitor the I
F
of the
boost diode. As stated above, the inverting input of the
current error amplifier is a virtual ground. Given this fact,
and the arrangement of the duty cycle modulator polarities
internal to the PFC, an increase in positive current from
the gain modulator will cause the output stage to increase
its duty cycle until the voltage on I
SENSE
is adequately
negative to cancel this increased current. Similarly, if the
gain modulator’s output decreases, the output duty cycle
will decrease, to achieve a less negative voltage on the
I
SENSE
pin.
There is a modest degree of gain contouring applied to the
transfer characteristic of the current error amplifier, to
increase its speed of response to current-loop
perturbations. However, the boost inductor will usually be
the dominant factor in overall current loop response.
Therefore, this contouring is significantly less marked than
that of the voltage error amplifier. This is illustrated in the
Typical Performance Characteristics.
Cycle-By-Cycle Current Limiter
The I
SENSE
pin, as well as being a part of the current
feedback loop, is a direct input to the cycle-by-cycle
current limiter for the PFC section. Should the input
voltage at this pin ever be more negative than -1V, the
output of the PFC will be disabled until the protection
flip-flop is reset by the clock pulse at the start of the next
PFC power cycle.
Overvoltage Protection
The OVP comparator serves to protect the power circuit
from being subjected to excessive voltages if the load
should suddenly change. A resistor divider from the high
voltage DC output of the PFC is fed to V
FB
. When the
voltage on V
FB
exceeds 2.7V, the PFC output driver is shut
down. The PWM section will continue to operate. The
OVP comparator has 125mV of hysteresis, and the PFC
will not restart until the voltage at V
FB
drops below 2.58V.
The V
FB
should be set at a level where the active and
passive external power components and the ML4826 are
within their safe operating voltages, but not so low as to
interfere with the boost voltage regulation loop.
19
VEAO
IEAO
VFB
IAC
VRMS
ISENSE
2.5V
-
+
20
2
4
3
VEA
-
+
IEA
+
-
VREF
1
AGND
11
PFC
OUTPUT
GAIN
MODULATOR
相關PDF資料 |
PDF描述 |
|---|---|
| ML4826IP-2 | PFC and Dual Output PWM Controller Combo |
| ML4826CP2 | PFC and Dual Output PWM Controller Combo |
| ML4826 | PFC and Dual Output PWM Controller Combo |
| ML4827CP-1 | Fault-Protected PFC and PWM Controller Combo |
| ML4827CP-2 | Fault-Protected PFC and PWM Controller Combo |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML4826IP2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ML4826IP-2 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:PFC and Dual Output PWM Controller Combo |
| ML4826IS-1 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:PFC and Dual Output PWM Controller Combo |
| ML4826IS-2 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:PFC and Dual Output PWM Controller Combo |
| ML4827 | 制造商:MICRO-LINEAR 制造商全稱:MICRO-LINEAR 功能描述:Fault-Protected PFC and PWM Controller Combo |
發布緊急采購，3分鐘左右您將得到回復。