- 您現在的位置：買賣IC網 > PDF目錄45332 > MKI41T56S00TR (STMICROELECTRONICS) 0 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | MKI41T56S00TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SOP-8 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 105K |
| 代理商： | MKI41T56S00TR |
11/16
MK41T56, MKI41T56
dicates the degree and direction of oscillator fre-
quency shift at the test temperature.
For example, a reading of 512.01024Hz would in-
dicate a +20ppm oscillator frequency error, requir-
ing a –10(XX001010) to be loaded into the
Calibration Byte for correction. Note that setting or
changing the Calibration Byte does not affect the
Frequency test output frequency.
OUTPUT DRIVER PIN
When the FT bit is not set, the FT/OUT pin be-
comes an output driver that reflects the contents of
D7 of the control register. In other words, when D6
of location 7 is a zero and D7 of location 7 is a zero
and then the FT/OUT pin will be driven low.
Note: The FT/OUT pin is open drain which re-
quires an external pull-up resistor.
Two methods are available for ascertaining how
much calibration a given MK41T56 may require.
The first involves simply setting the clock, letting it
run for a month and comparing it to a known accu-
rate reference (like WWV broadcasts). While that
may seem crude, it allows the designer to give the
end user the ability to calibrate his clock as his en-
vironment may require, even after the final product
is packaged in a non-user serviceable enclosure.
All the designer has to do is provide a simple utility
that accessed the Calibration byte.
The second approach is better suited to a manu-
facturing environment, and involves the use of
some test equipment. When the Frequency Test
(FT) bit, the seventh-most significant bit in the
Control Register, is set to a '1', and the oscillator is
running at 32,768Hz, the FT/OUT pin of the device
will toggle at 512Hz. Any deviation from 512Hz in-
Figure 14. Clock Calibration
AI00594B
NORMAL
POSITIVE
CALIBRATION
NEGATIVE
CALIBRATION
相關PDF資料 |
PDF描述 |
|---|---|
| ML2035IP | 1-BIT, DSP-NUM CONTROLLED OSCILLATOR, PDIP8 |
| ML54053 | IDE COMPATIBLE, FLASH MEMORY DRIVE CONTROLLER, PQFP120 |
| ML610Q346J-NNNTB | 8-BIT, FLASH, 4.2 MHz, RISC MICROCONTROLLER, PQFP64 |
| ML610Q409-NNNTBZ03A | RISC MICROCONTROLLER, PQFP100 |
| ML610Q408-NNNTBZ03A | RISC MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MKI50-06A7 | 功能描述:IGBT 模塊 50 Amps 600V RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝: |
| MKI50-06A7T | 功能描述:分立半導體模塊 50 Amps 600V RoHS:否 制造商:Infineon Technologies 產品:Thyristor Power Modules 類型:Phase Controls 安裝風格:Screw 封裝 / 箱體:DT61 封裝: |
| MKI50-12E7 | 功能描述:分立半導體模塊 IGBT (NPT3) 1200V 50A RoHS:否 制造商:Infineon Technologies 產品:Thyristor Power Modules 類型:Phase Controls 安裝風格:Screw 封裝 / 箱體:DT61 封裝: |
| MKI50-12F7 | 功能描述:IGBT 模塊 50 Amps 1200V RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝: |
| MKI65-06A7T | 功能描述:分立半導體模塊 65 Amps 600V RoHS:否 制造商:Infineon Technologies 產品:Thyristor Power Modules 類型:Phase Controls 安裝風格:Screw 封裝 / 箱體:DT61 封裝: |
發布緊急采購，3分鐘左右您將得到回復。