參數資料
型號: MK3732-17STR
廠商: IDT, Integrated Device Technology Inc
文件頁數: 3/7頁
文件大?。?/td> 0K
描述: IC VCXO CLK SOURCE ADSL 16-SOIC
標準包裝: 2,500
類型: PLL 時鐘合成器,VCXO
PLL:
輸入: 晶體
輸出: CMOS
電路數: 1
比率 - 輸入:輸出: 2:2
差分 - 輸入:輸出: 無/無
頻率 - 最大: 49.46MHz
除法器/乘法器: 無/無
電源電壓: 3.15 V ~ 3.45 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 16-SOIC
包裝: 帶卷 (TR)
MK3732-17
ADSL VCXO CLOCK SOURCE
VCXO AND SYNTHESIZER
IDT / ICS ADSL VCXO CLOCK SOURCE
3
MK3732-17
REV D 050803
External Component Selection
The MK3732-17 requires a minimum number of external
components for proper operation.
Decoupling Capacitors
Decoupling capacitors of 0.01
F should be connected
between VDD and GND on pins 3 and 6, and on pins 13 and
14, as close to the MK3732-17 as possible. For optimum
device performance, the decoupling capacitors should be
mounted on the component side of the PCB. Avoid the use
of vias in the decoupling circuit.
Series Termination Resistor
When the PCB traces between the clock outputs and the
loads are over 1 inch, series termination should be used. To
series terminate a 50
trace (a commonly used trace
impedance) place a 33
resistor in series with the clock
line, as close to the clock output pin as possible. The
nominal impedance of the clock output is 20
.
Quartz Crystal
The MK3732-17 VCXO function consists of the external
crystal and the integrated VCXO oscillator circuit. To assure
the best system performance (frequency pull range) and
reliability, a crystal device with the recommended
parameters must be used, and the layout guidelines
discussed in the following section must be followed.
The frequency of oscillation of a quartz crystal is determined
by its “cut” and by the load capacitors connected to it. The
MK3732-17 incorporates on-chip variable load capacitors
that “pull” (change) the frequency of the crystal. The crystal
specified for use with the MK3732-17 is designed to have
zero frequency error when the total of on-chip + stray
capacitance is 14pF.
The external crystal must be connected as close to the chip
as possible and should be on the same side of the PCB as
the MK3732-17. There should be no vias between the
crystal pins and the X1 and X2 device pins. There should be
no signal traces underneath or close to the crystal.
Please see application note MAN05 for recommended
crystal parameters and suppliers.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors on the
PCB is optional. The need for these capacitors is
determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture and
frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
To determine the need for and value of the crystal
adjustment capacitors, you will need a PC board of your final
layout, a frequency counter capable of about 1 ppm
resolution and accuracy, two power supplies, and some
samples of the crystals which you plan to use in production,
along with measured initial accuracy for each crystal at the
specified crystal load capacitance, CL.
To determine the value of the crystal capacitors:
1. Connect VDD of the MK3732-17 to 3.3V. Connect pin 4 of
the MK3732-17 to the second power supply. Adjust the
voltage on pin 4 to 0V. Measure and record the frequency of
the CLK output.
2. Adjust the voltage on pin 4 to 3.3V. Measure and record
the frequency of the same output.
To calculate the centering error:
Where:
ftarget = nominal crystal frequency
errorxtal =actual initial accuracy (in ppm) of the crystal being
measured
If the centering error is less than ±25 ppm, no adjustment is
needed. If the centering error is more than 25ppm negative,
the PC board has excessive stray capacitance and a new
PCB layout should be considered to reduce stray
capacitance. (Alternately, the crystal may be re-specified to
a higher load capacitance. Contact ICS for details.) If the
centering error is more than 25ppm positive, add identical
fixed centering capacitors from each crystal pin to ground.
The value for each of these caps (in pF) is given by:
Error
10
6
x
f3.3V ftet
arg
()
f
0V
f
tet
arg
()
+
f
tet
arg
------------------------------------------------------------------------------
error
xtal
=
相關PDF資料
PDF描述
VI-JWM-MZ-F2 CONVERTER MOD DC/DC 10V 25W
VI-JW3-MZ-F2 CONVERTER MOD DC/DC 24V 25W
MK2746GLFTR IC CLK SOURCE DVD/MPEG 16-TSSOP
MK2746-01GLFTR IC CLK SOURCE USB-DVD 16-TSSOP
MK1716-01RLFTR IC CLK SOURCE SER PROGR 28-QSOP
相關代理商/技術參數
參數描述
MK3732-19GLF 制造商:Integrated Device Technology Inc 功能描述:MK3732-19GLF - Bulk
MK3732-19GLFTR 制造商:Integrated Device Technology Inc 功能描述:MK3732-19GLFTR - Tape and Reel
MK3732-22RLF 功能描述:IC VCXO BLUE-RAY DISC 20-QSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP (0.240",6.10mm 寬) 供應商設備封裝:64-TSSOP 包裝:管件
MK3732-22RLFTR 功能描述:IC VCXO BLUE-RAY DISC 20-QSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP (0.240",6.10mm 寬) 供應商設備封裝:64-TSSOP 包裝:管件
MK3741SLF 制造商:Integrated Device Technology Inc 功能描述:MK3741SLF - Bulk