- 您現在的位置：買賣IC網 > PDF目錄45330 > MK3712SLF (INTEGRATED DEVICE TECHNOLOGY INC) 27 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF資料下載
參數資料
| 型號： | MK3712SLF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 27 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 73K |
| 代理商： | MK3712SLF |
3.3 VOLT SET-TOP BOX VCXO
MDS 3712 B
3
Revision 091801
Int egrat ed C i rcuit Syste ms q 525 R a ce S t r eet, San Jose, CA 95126 q t e l (40 8 ) 295 -9800 q
w w w. icst . c om
MK3712
External Component Selection
The MK3712 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected
between VDD (pin 2) and GND (pin 4), as close to
these pins as possible. For optimum device
performance, the decoupling capacitor should be
mounted on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance) place a 33
resistor in series
with the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
Quartz Crystal
The MK3712 VCXO function consists of the external
crystal and the integrated VCXO oscillator circuit. To
assure the best system performance (frequency pull
range) and reliability, a crystal device with the
recommended parameters (shown below) must be
used, and the layout guidelines discussed in the
following section must be followed.
The frequency of oscillation of a quartz crystal is
determined by its “cut” and by the load capacitors
connected to it. The MK3712 incorporates on-chip
variable load capacitors that “pull” (change) the
frequency of the crystal. The crystal specified for use
with the MK3712 is designed to have zero frequency
error when the total of on-chip + stray capacitance is
14pF.
Recommended Crystal Parameters:
Initial Accuracy at 25
°C±20 ppm
Temperature Stability
±30 ppm
Aging
±20 ppm
Load Capacitance
14 pf
Shunt Capacitance, C0
7 pF Max
C0/C1 Ratio
250 Max
Equivalent Series Resistance
35
Max
The external crystal must be connected as close to the
chip as possible and should be on the same side of the
PCB as the MK3712. There should be no via’s between
the crystal pins and the X1 and X2 device pins. There
should be no signal traces underneath or close to the
crystal.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors
on the PCB is optional. The need for these capacitors
is determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture
and frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
To determine the need for and value of the crystal
adjustment capacitors, you will need a PC board of
your final layout, a frequency counter capable of about
1 ppm resolution and accuracy, two power supplies,
and some samples of the crystals which you plan to
use in production, along with measured initial accuracy
for each crystal at the specified crystal load
capacitance, CL.
To determine the value of the crystal capacitors:
1. Connect VDD of the MK3712 to 3.3V. Connect pin 3
of the MK3712 to the second power supply. Adjust the
voltage on pin 3 to 0V. Measure and record the
frequency of the CLK output.
2. Adjust the voltage on pin 3 to 3.3V. Measure and
record the frequency of the same output.
To calculate the centering error:
Where:
ftarget = nominal crystal frequency
errorxtal =actual initial accuracy (in ppm) of the crystal
being measured
If the centering error is less than ±25 ppm, no
adjustment is needed. If the centering error is more
than 25ppm negative, the PC board has excessive
stray capacitance and a new PCB layout should be
Error
10
6
x
f
3.0V
f
tet
arg
–
()
f
0V
f
tet
arg
–
()
+
f
tet
arg
------------------------------------------------------------------------------
error
xtal
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| MK3712DTRLF | 27 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK3712SLF | 27 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK3715STR | 108 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK3720ALF | 54 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| MK3720SLF | 54 MHz, OTHER CLOCK GENERATOR, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK3713 | 制造商:ICS 制造商全稱:ICS 功能描述:Low Cost 3.3 Volt VCXO |
| MK3713S | 制造商:ICS 制造商全稱:ICS 功能描述:Low Cost 3.3 Volt VCXO |
| MK3713STR | 制造商:ICS 制造商全稱:ICS 功能描述:Low Cost 3.3 Volt VCXO |
| MK3715 | 制造商:ICS 制造商全稱:ICS 功能描述:LOW COST 3.3 VOLT VCXO |
| MK3715S | 制造商:ICS 制造商全稱:ICS 功能描述:LOW COST 3.3 VOLT VCXO |
發布緊急采購，3分鐘左右您將得到回復。