- 您現在的位置：買賣IC網 > PDF目錄377966 > MIC2593 (意法半導體) Dual-Slot PCI Hot Plug Controller PDF資料下載
參數資料
| 型號： | MIC2593 |
| 廠商： | 意法半導體 |
| 英文描述： | Dual-Slot PCI Hot Plug Controller |
| 中文描述： | 雙插槽的PCI熱插拔控制器 |
| 文件頁數： | 13/26頁 |
| 文件大?。?/td> | 170K |
| 代理商： | MIC2593 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
April 2004
13
M9999-042204
MIC2593
Micrel
MAIN[A/B]PG
(3)
3VAUX_UV[A/B]
(1)
12VOUT_UV[A/B]
(1)
3VOUT_UV[A/B]
(1)
AUX[A/B]PG
(2)
V
STBY[A/B]
V
STBY[A/B]
Notes:
1. Internal flag
2. CNTRL[A/B] Register Bit D[7]
3. CNTRL[A/B] Register Bit D[6]
Figure 7. Power-Good Status Logic Diagram
Slot B, CFILTER[B] is located at Pin 35. For a given response
time, the value for CFILTER[A/B] is given by:
CFILTER A B
F
t
ms
(
I
A
V
V
10
FLT A B
FILTER
( )
×
FILTER
3
)
)
(
)
μ
=
×
μ
where t
FLT[A/B]
is the selected overcurrent response time
and I
FILTER
and V
FILTER
are specified in the
“
Electrical
Characteristics
”
table.
Thermal Shutdown
The internal +12V,
–
12V, and V
AUX
MOSFETs are protected
against damage not only by current limiting, but by dual-mode
overtemperature protection as well. Each slot controller on
the MIC2593 is thermally isolated from the other. Should an
overcurrent condition raise the junction temperature of one
slot
’
s controller and internal pass elements to 140
°
C, all of the
outputs for that slot (including V
AUX
) will be shut off, and the
slot
’
s /FAULT output will be asserted. The other slot
’
s opera-
tion will remain unaffected. However, should the MIC2593
’
s
overall die temperature exceed 160
°
C, both slots (all outputs,
including V
AUXA
and V
AUXB
) will be shut off, whether or not a
current limit condition exists. A 160
°
C overtemperature con-
dition additionally sets the overtemperature bit (OT_INT) in
the Common Status Register.
Output Power-Good Status
For the MIC2593,
“
Power-is-Good
”
is valid on a slot when the
outputs of the four MAIN supplies (12V,
–
12V, 5V, and 3.3V)
and the auxiliary supply output are all above their respective
power-good thresholds specified in the
“
Electrical Character-
istics
”
table. The power-good status of either slot is verified by
polling the CNTRL[A/B] Register Bits D[7:6]. CNTRL[A/B]
Register Bits D[7] and D[6] indicate output power-good status
for the AUX supply and MAIN supplies, respectively. Figure
7 below illustrates an equivalent logic circuit that determines
the output power-good status for the MAIN and AUX supplies.
General Purpose Input (GPI) Pins
Two pins on the MIC2593 are available for use as GPI pins.
The logic state of each of these pins can be determined by
polling Bits [4:5] of Common Status Register. Both of these
inputs are compliant to 3.3V. If unused, connect the GPI[A/B]
pins to GND.
Fault Reporting and /INT Interrupt Generation
SMI-only Control Applications
In applications where the MIC2593 is controlled only by the
SMI, the ON[A/B] and AUXEN[A/B] should be connected to
GND as shown in Figure 6. In this case, the MIC2593
’
s
/FAULT[A/B] outputs and STAT[A/B] Register Bit D[7]
(FAULT[A/B]) are not activated, as fault status is determined
by polling STAT[A/B] Register Bits D[4:0] and CS (Common
Status) Register Bits D[2:1]. Individual fault bits in STAT[A/B]
and CS are asserted after power-on-reset when:
Either or both CNTRL[A/B] Register Bits D[1:0] are asserted,
AND
12VIN[A/B], 12MVIN[A/B], 5VIN[A/B], 3VIN[A/B],
or VSTBY[A/B] input voltage is lower than its
respective ULVO threshold, OR
The fast OC circuit breaker[A/B] has tripped, OR
The slow OC circuit breaker[A/B] has tripped AND
its filter timeout has expired, OR
The slow OC circuit breaker[A/B] has tripped AND
Slot[A/B] die temperature exceeds 140
°
C, OR
The MIC2593
’
s global die temperature exceeds
160
°
C
To clear any one or all STAT[A/B] Register Bits D[4:0] and/or
CS Register Bits D[2:1] once asserted, a software subroutine
can perform an
“
echo reset
”
where a Logical
“
1
”
is written
back to those register bit locations that have indicated a fault.
The open-drain, active-LOW /INT output signal is activated
after power-on-reset when the INTMSK bit (CS Register Bit
D[3]) has been reset to Logical
“
0
”
. Once activated, the /INT
output is asserted by any one of the fault conditions listed
above and de-asserted when one or all STAT[A/B] Register
Bits D[4:0] and/or CS Register Bits D[2:1] are reset upon the
execution of an SMBus
“
echo reset
”
WRITE_BYTE cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2593-2BTQ | Dual-Slot PCI Hot Plug Controller |
| MIC2593-5BTQ | Dual-Slot PCI Hot Plug Controller |
| MIL-PRF-19500 | SEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, LOW-POWER TYPES 2N2484, 2N2484UA, 2N2484UB, JAN, JANTX, JANTXV, JANS, JANHC, AND JANKC |
| MINISO-8 | 8-LEAD MINI SMALL OUTLINE |
| MJ2400 | Inrush Current Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC2593-2BTQ | 功能描述:IC CTRLR HOTPLUG PCI DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2593-2BTQ TR | 功能描述:IC PCI HOT PLUG CTLR DUAL 48TQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| MIC2593-2YTQ | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2593-2YTQ TR | 功能描述:熱插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MIC2594-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。