- 您現在的位置：買賣IC網 > PDF目錄98014 > MGSF3454VT1 (ON SEMICONDUCTOR) 4.2 A, 30 V, 0.065 ohm, N-CHANNEL, Si, POWER, MOSFET PDF資料下載
參數資料
| 型號： | MGSF3454VT1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | JFETs |
| 英文描述： | 4.2 A, 30 V, 0.065 ohm, N-CHANNEL, Si, POWER, MOSFET |
| 封裝： | TSOP-6 |
| 文件頁數： | 9/13頁 |
| 文件大小： | 167K |
| 代理商： | MGSF3454VT1 |
MGSF3454VT1
http://onsemi.com
353
INFORMATION FOR USING THE TSOP–6 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the
total design. The footprint for the semiconductor packages
must be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
mm
inches
1.9
0.039
1.0
0.094
0.7
0.074
2.4
0.028
0.95
0.037
0.95
0.037
TSOP–6 POWER DISSIPATION
The power dissipation of the TSOP–6 is a function of the
drain pad size. This can vary from the minimum pad size
for soldering to a pad size given for maximum power
dissipation. Power dissipation for a surface mount device is
determined by TJ(max), the maximum rated junction
temperature of the die, R
θJA, the thermal resistance from
the device junction to ambient, and the operating
temperature, TA. Using the values provided on the data
sheet for the TSOP–6 package, PD can be calculated as
follows:
PD =
TJ(max) – TA
R
θJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values
into the equation for an ambient temperature TA of 25°C,
one can calculate the power dissipation of the device which
in this case is 2.0 watts.
PD =
150
°C – 25°C
62.5
°C/W
= 2.0 watts
The 62.5
°C/W for the TSOP–6 package assumes the use
of the recommended footprint on a glass epoxy printed
circuit board to achieve a power dissipation of 2.0 watts.
There are other alternatives to achieving higher power
dissipation from the TSOP–6 package. Another alternative
would be to use a ceramic substrate or an aluminum core
board such as Thermal Clad
t. Using a board material such
as Thermal Clad, an aluminum core board, the power
dissipation can be doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within
a short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering
method, the difference shall be a maximum of 10
°C.
The soldering temperature and time shall not exceed
260
°C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and
result in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied
during cooling.
* Soldering a device without preheating can cause
excessive thermal shock and stress which can result in
damage to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| MGSF3454V | 4.2 A, 30 V, 0.065 ohm, N-CHANNEL, Si, POWER, MOSFET |
| MGSF3454XT1 | 1750 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MGSF3454X | 1750 mA, 30 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET |
| MGSF3455VT1 | 3.5 A, 30 V, 0.1 ohm, P-CHANNEL, Si, POWER, MOSFET |
| MGSF3455VT3 | 3.5 A, 30 V, 0.1 ohm, P-CHANNEL, Si, POWER, MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MGSF3454XT1 | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MGSF3455VT1 | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MGSF3455XT1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MGSG12 | 功能描述:LED替換燈-基于LED RoHS:否 制造商:Chicago Miniature 照明顏色:Red 光強度: 電壓額定值:115 V 封裝: |
| MGSG24 | 功能描述:LED替換燈-基于LED RoHS:否 制造商:Chicago Miniature 照明顏色:Red 光強度: 電壓額定值:115 V 封裝: |
發布緊急采購，3分鐘左右您將得到回復。