- 您現在的位置：買賣IC網 > PDF目錄25639 > MD80C52CXXX-16SCD (ATMEL CORP) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MD80C52CXXX-16SCD |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | 0.600 INCH, CERAMIC, DIP-40 |
| 文件頁數： | 46/80頁 |
| 文件大?。?/td> | 5152K |
| 代理商： | MD80C52CXXX-16SCD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
246
XMEGA A [MANUAL]
8077I–AVR–11/2012
DREIF is cleared by writing DATA. When interrupt-driven data transmission is used, the data register empty interrupt
routine must either write new data to DATA in order to clear DREIF or disable the data register empty interrupt. If not, a
new interrupt will occur directly after the return from the current interrupt.
Bit 4 – FERR: Frame Error
The FERR flag indicates the state of the first stop bit of the next readable frame stored in the receive buffer. The bit is set
if the received character had a frame error, i.e., the first stop bit was zero, and cleared when the stop bit of the received
data is one. This bit is valid until the receive buffer (DATA) is read. FERR is not affected by setting the number of stop
bits used, as it always uses only the first stop bit. Always write this bit location to zero when writing the STATUS register.
This flag is not used in master SPI mode operation.
Bit 3 – BUFOVF: Buffer Overflow
This flag indicates data loss due to a receiver buffer full condition. This flag is set if a buffer overflow condition is
detected. A buffer overflow occurs when the receive buffer is full (two characters) with a new character waiting in the
receive shift register and a new start bit is detected. This flag is valid until the receive buffer (DATA) is read. Always write
this bit location to zero when writing the STATUS register.
This flag is not used in master SPI mode operation.
Bit 2 – PERR: Parity Error
If parity checking is enabled and the next character in the receive buffer has a parity error, this flag is set. If parity check
is not enabled, this flag will always be read as zero. This bit is valid until the receive buffer (DATA) is read. Always write
this bit location to zero when writing the STATUS register. For details on parity calculation, refer to “Parity Bit Calculation”
This flag is not used in master SPI mode operation.
Bit 1 – Reserved
This bit is unused and reserved for future use. For compatibility with future devices, always write this bit to zero when this
register is written.
Bit 0 – RXB8: Receive Bit 8
RXB8 is the ninth data bit of the received character when operating with serial frames with nine data bits. When used,
this bit must be read before reading the low bits from DATA.
This bit is unused in master SPI mode operation.
21.15.3 CTRLA – Control register A
Bit 7:6 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always write these bits to zero
when this register is written.
Bit 5:4 – RXCINTLVL[1:0]: Receive Complete Interrupt Level
These bits enable the receive complete interrupt and select the interrupt level, as described in “Interrupts and
Programmable Multilevel Interrupt Controller” on page 125. The enabled interrupt will be triggered when the RXCIF flag
in the STATUS register is set.
Bit 3:2 – TXCINTLVL[1:0]: Transmit Complete Interrupt Level
These bits enable the transmit complete interrupt and select the interrupt level, as described in “Interrupts and
Programmable Multilevel Interrupt Controller” on page 125. The enabled interrupt will be triggered when the TXCIF flag
in the STATUS register is set.
Bit
765
43210
+0x03
–
RXCINTLVL[1:0]
TXCINTLVL[1:0]
DREINTLVL[1:0]
Read/Write
R
R/W
Initial Value
0
相關PDF資料 |
PDF描述 |
|---|---|
| MQ80C52TXXX-25SCR | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44 |
| MQ80C52CXXX-30/883D | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQFP44 |
| MR83C154XXX-25P883 | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44 |
| MS80C51-12D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44 |
| MT80C51T-16R | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MD80C86 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C862 | 制造商:Intel 功能描述:PROCESSOR:MICRO-PROCESSOR |
| MD80C86-2 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor |
| MD80C86-2/883 | 制造商:Intersil Corporation 功能描述:MPU 16BIT CMOS 8MHZ 40CDIP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:CPU 16BILT 5V CMOS 8MHZ 40CDIP - Bulk |
| MD80C86-2/B | 制造商:Intersil Corporation 功能描述:MPU 16BIT CMOS 8MHZ 40CDIP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。