OPERATIONAL MODES In order to select and ac" />
參數資料
型號: MCZ33742EG
廠商: Freescale Semiconductor
文件頁數: 26/71頁
文件大?。?/td> 0K
描述: IC SYSTEM BASIS CHIP CAN 28-SOIC
標準包裝: 26
應用: 自動
電流 - 電源: 42mA
電源電壓: 5.5 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 28-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 28-SOIC W
包裝: 管件
產品目錄頁面: 808 (CN2011-ZH PDF)
Analog Integrated Circuit Device Data
32
Freescale Semiconductor
33742
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
In order to select and activate the cyclic sense wake-up from the L0:L3 inputs, the WUR register must be configured with the
appropriate level sensitivity and the LPC register must be configured with 1xx1 data (bit LX2HS set at 1 and bit HSAUTO set
at 1. The wake-up mode selection (direct or cyclic sense) is valid for all four wake-up inputs.
FORCED WAKE-UP
The SBC can wake-up automatically after a predetermined time spent in Sleep or Stop mode. Cyclic Sense and Forced Wake-
up are exclusive. If Forced Wake-up is enabled (FWU bit set to 1 in the LPC register), Cyclic Sense cannot be enabled.
CAN INTERFACE WAKE-UP
The SBC incorporates a high-speed 1.0 Mbps CAN physical interface. It is compatible with ISO 11898-2 standard. The
operation of the CAN physical interface is controlled through the SPI. The CAN operating modes are independent of the 33742
operational modes.
The SBC can wake up from a CAN message if the CAN wake-up feature is enabled. Refer to the section titled LOGIC
COMMANDS AND REGISTERS beginning on page 46 for details of the wake-up detection.
SPI WAKE-UP
The 33742 can be awakened by changes on the CS pin in Sleep or Stop modes. Wake-up is detected as a LOW-to-HIGH level
transition on the CS pin. In the Stop mode, this corresponds to a condition where an MCU and the SBC are both in the Stop mode
and when the application wake-up event comes through the MCU.
33742 POWER-UP AND WAKE-UP FROM SLEEP MODE
After device or system power-up, or after the SBC awakens from Sleep mode, the 33742S enters into the Reset mode prior
to moving into Normal Request mode.
Figure 13, shows the device state diagram. Figure 14, shows device operation after power-up.
相關PDF資料
PDF描述
H2MXH-1618M DIP CABLE - HDM16H/AE16M/X
PCK0G331MCO1GS CAP ALUM 330UF 4V 20% SMD
SDR0805-681KL INDUCTOR POWER 680UH 10% SMD
AD587JR-REEL IC VREF SERIES PREC 10V 8-SOIC
B82422A3151K100 INDUCTOR .15UH 390MA 1210 10%
相關代理商/技術參數
參數描述
MCZ33742EGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742SEG 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742SEGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33780EG 功能描述:多路器開關 IC DBUS MASTER RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
MCZ33780EG 制造商:Freescale Semiconductor 功能描述:DUAL DBUS MASTER INTERFACE 16SOIC