參數資料
型號： MCP9808T-E/MS
廠商： Microchip Technology
文件頁數： 14/52頁
文件大小： 1085K
描述： IC TEMP SENSOR DGTL I2C 8MSOP
標準包裝： 2,500
功能： 溫度監控系統（傳感器）
傳感器類型： 內部
感應溫度： -40°C ~ 125°C
精確度： ±1°C
拓?fù)洌?/td> ADC（三角積分型），寄存器庫
輸出類型： 2 線串行，I²C?/SMBUS?
輸出警報： 是
輸出風扇： 是
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
MCP9808
DS25095A-page 14
?2011 Microchip Technology Inc.
4.1.4
ADDRESS BYTE
Following the Start condition, the host must transmit an
8-bit address byte to the MCP9808. The address for the
MCP9808 temperature sensor is 0011,A2,A1,A0 in
binary, where the A2, A1 and A0 bits are set externally
by connecting the corresponding pins to V
DD
 1 or GND
0. The 7-bit address, transmitted in the serial bit stream,
must match the selected address for the MCP9808 to
respond with an ACK. Bit 8 in the address byte is a
read/write bit. Setting this bit to 1 commands a read
operation, while 0 commands a write operation (see
Figure 4-1).
FIGURE 4-1:
Device Addressing.
4.1.5
DATA VALID
After the Start condition, each bit of data in the
transmission needs to be settled for a time specified by
t
SU-DATA
 before SCL toggles from low-to-high (see the
Sensor Serial Interface Timing Specifications section). 
4.1.6
ACKNOWLEDGE (ACK/NAK)
Each   receiving   device,   when   addressed,   must
generate an ACK bit after the reception of each byte.
The master device must generate an extra clock pulse
for ACK to be recognized.
The Acknowledging device pulls down the SDA line for
t
SU-DATA
 before the low-to-high transition of SCL from
the master. SDA also needs to remain pulled down for
t
H-DATA
 after a high-to-low transition of SCL.
During read, the master must signal an End-of-Data
(EOD) to the slave, by not generating an ACK bit
(NAK), once the last bit has been clocked out of the
slave. In this case, the slave will leave the data line
released to enable the master to generate the Stop
condition.
4.1.7
TIME-OUT
If the SCL stays low or high for the time specified by
t
OUT
, the MCP9808 temperature sensor resets the
serial interface. This dictates the minimum clock speed
as outlined in the specification.
1   2   3   4   5   6   7   8   9
SCL
SDA
0   1  1  A2 A1 A0
Start
Address Byte
Slave
Address
R/W
 
MCP9808 Response
Code
Address
A
C
K
0
See Table 3-2.
相關PDF資料
PDF描述
MCZ33998EGR2 IC REG CHARGEPUMP/LINEAR 24SOIC
MCZ34652EFR2 IC HOTSWAP CTRLR 2A NEG 16SOIC
MCZ34653EFR2 IC HOTSWAP CTRLR 1A NEG 8-SOIC
MCZ34670EG IC POE CURR MODE SW REG 20-SOIC
MIC184BM TR IC SUPERVISOR LOCAL/REMOTE 8SOIC
相關代理商/技術參數
參數描述
MCP98242 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD
MCP98242_09 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD
MCP98242-BE/MC 制造商:Microchip Technology Inc 功能描述:TEMP SENSOR DGTL SERL (2-WIRE, - Bulk
MCP98242-BE/MNY 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD
MCP98242-BE/ST 功能描述:板上安裝溫度傳感器 JEDEC DIMM Serial output temp sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*