參數資料
型號: MCP4162T-503E/MS
廠商: Microchip Technology
文件頁數: 24/88頁
文件大?。?/td> 0K
描述: IC POT DGTL SNGL 50K RHEO 8MSOP
標準包裝: 2,500
系列: WiperLock™
接片: 257
電阻(歐姆): 50k
電路數: 1
溫度系數: 標準值 150 ppm/°C
存儲器類型: 易失
接口: 4 線 SPI(芯片選擇)
電源電壓: 1.8 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 帶卷 (TR)
MCP414X/416X/424X/426X
DS22059B-page 30
2008 Microchip Technology Inc.
4.2.1
NON-VOLATILE MEMORY
(EEPROM)
This memory can be grouped into two uses of
non-volatile memory. These are:
The non-volatile wipers starts functioning below the
devices VPOR/VBOR trip point.
4.2.1.1
General Purpose Registers
These locations allow the user to store up to 10 (9-bit)
locations worth of information.
4.2.1.2
Non-Volatile Wiper Registers
These locations contain the wiper values that are
loaded into the corresponding volatile wiper register
whenever the device has a POR/BOR event. There are
up to two registers, one for each resistor network.
The non-volatile wiper register enables stand-alone
operation of the device (without Microcontroller control)
after being programmed to the desired value.
4.2.1.3
Factory Initialization of Non-Volatile
Memory (EEPROM)
The Non-Volatile Wiper values will be initialized to
mid-scale value. This is shown in Table 4-2.
The General purpose EEPROM memory will be
programmed to a default value of 0xFF.
It is good practice in the manufacturing flow to
configure the device to your desired settings.
TABLE 4-2:
DEFAULT FACTORY
SETTINGS SELECTION
4.2.1.4
Special Features
There are 3 non-volatile bits that are not directly
mapped into the address space. These bits control the
following functions:
EEPROM Write Protect
WiperLock Technology for Non-Volatile Wiper 0
WiperLock Technology for Non-Volatile Wiper 1
The operation of WiperLock Technology is discussed in
. The state of the WL0, WL1, and WP bits
is reflected in the STATUS register (see Register 4-1).
EEPROM Write Protect
All internal EEPROM memory can be Write Protected.
When EEPROM memory is Write Protected, Write
commands to the internal EEPROM are prevented.
Write Protect (WP) can be enabled/disabled by two
methods. These are:
External WP Hardware pin (MCP42X1 devices
only)
Non-Volatile configuration bit
High Voltage commands are required to enable and
disable the nonvolatile WP bit. These commands are
To write to EEPROM, both the external WP pin and the
internal WP EEPROM bit must be disabled. Write
Protect does not block commands to the volatile
registers.
4.2.2
VOLATILE MEMORY (RAM)
There are four Volatile Memory locations. These are:
Volatile Wiper 0
Volatile Wiper 1
(Dual Resistor Network devices only)
Status Register
Terminal Control (TCON) Register
The volatile memory starts functioning at the RAM
retention voltage (VRAM).
Resist
an
ce
Code
Ty
p
ic
a
l
R
AB
Va
lu
e
Default
POR
Wi
p
e
rS
e
tt
in
g
Wiper
Code
W
iper
L
o
ck
T
ech
no
lo
gy
a
n
d
W
rite
Pro
tect
Settin
g
8-bit 7-bit
-502
5.0 k
Ω
Mid-scale 80h
40h
Disabled
-103
10.0 k
Ω Mid-scale 80h
40h
Disabled
-503
50.0 k
Ω Mid-scale 80h
40h
Disabled
-104
100.0 k
Ω Mid-scale 80h
40h
Disabled
相關PDF資料
PDF描述
VI-B1V-MV CONVERTER MOD DC/DC 5.8V 150W
X1288S16I-2.7T1 IC RTC/CAL/CPU SUP EE 16-SOIC
MCP4162T-502E/MS IC POT DGTL SNGL 5K RHEO 8MSOP
X1288S16I-2.7AT1 IC RTC/CAL/CPU SUP EE 16-SOIC
VE-B1V-MV CONVERTER MOD DC/DC 5.8V 75W
相關代理商/技術參數
參數描述
MCP4162T-503I/MF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory
MCP4162T-503I/ML 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory
MCP4162T-503I/MS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory
MCP4162T-503I/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory
MCP4162T-503I/SL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:7/8-Bit Single/Dual SPI Digital POT with Non-Volatile Memory