- 您現在的位置：買賣IC網 > PDF目錄383589 > MCP41100 (Microchip Technology Inc.) Single/Dual Digital Potentiometer with SPI⑩ Interface PDF資料下載
參數資料
| 型號： | MCP41100 |
| 廠商： | Microchip Technology Inc. |
| 元件分類： | 數字電位計 |
| 英文描述： | Single/Dual Digital Potentiometer with SPI⑩ Interface |
| 中文描述： | 單/雙數字電位器接口與SPI⑩ |
| 文件頁數： | 13/33頁 |
| 文件大?。?/td> | 682K |
| 代理商： | MCP41100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
2003 Microchip Technology Inc.
DS11195C-page 13
MCP41XXX/42XXX
4.0
APPLICATIONS INFORMATION
The MCP41XXX/42XXX devices are 256 position
single and dual digital potentiometers that can be used
in place of standard mechanical pots. Resistance val-
ues of 10 k
,
50 k
and
100 k
are available. As
shown in Figure 4-1, each potentiometer is made up of
a variable resistor and an 8-bit (256 position) data reg-
ister that determines the wiper position. There is a
nominal wiper resistance of 52
for the 10 k
version,
125
for the 50 k
and 100 k
versions. For the dual
devices, the channel-to-channel matching variation is
less than 1%. The resistance between the wiper and
either of the resistor endpoints varies linearly according
to the value stored in the data register. Code 00h
effectively connects the wiper to the B terminal. At
power-up, all data registers will automatically be loaded
with the mid-scale value (80h). The serial interface pro-
vides the means for loading data into the shift register,
which is then transferred to the data registers. The
serial interface also provides the means to place indi-
vidual potentiometers in the shutdown mode for maxi-
mum power savings. The SHDN pin can also be used
to put all potentiometers in shutdown mode and the RS
pin is provided to set all potentiometers to mid-scale
(80h).
FIGURE 4-1:
data register 1 are 8-bit registers allowing 256 positions for each wiper. Standard SPI pins are used with
the addition of the Shutdown (SHDN) and Reset (RS) pins. As shown, reset affects the data register and
wipers, bringing them to mid-scale. Shutdown disconnects the A terminal and connects the wiper to B,
without changing the state of the data registers.
Block diagram showing the MCP42XXX dual digital potentiometer. Data register 0 and
When laying out the circuit for your digital potentiome-
ter, bypass capacitors should be used. These capaci-
tors should be placed as close as possible to the device
pin. A bypass capacitor value of 0.1 μF is recom-
mended. Digital and analog traces should be separated
as much as possible on the board, with no traces run-
ning underneath the device or the bypass capacitor.
Extra precautions should be taken to keep traces with
high-frequency signals (such as clock lines) as far as
possible from analog traces. Use of an analog ground
plane is recommended in order to keep the ground
potential the same for all devices on the board.
RDAC1
SCK
SO
SI
Decode
Logic
16-bit Shift Register
PA0
PB0
PW0
RDAC2
Data Register 1
CS
RS
SHDN
D7
D0
Data Register 0
D7
D0
D7
D0
PA1
PB1
PW1
V
DD
A
B
W
V
DD
M
μC
To Application
Circuit
0.1 uF
0.1 uF
Data Lines
相關PDF資料 |
PDF描述 |
|---|---|
| MCP41100T | Single/Dual Digital Potentiometer with SPI⑩ Interface |
| MCP41XXX | 400000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| MCP42010 | Single/Dual Digital Potentiometer with SPI Interface(單/雙數字電位器，帶SPI接口) |
| MCP42050 | Single/Dual Digital Potentiometer with SPI Interface(單/雙數字電位器，帶SPI接口) |
| MCP450 | 400000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP41100E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
| MCP41100-E/P | 功能描述:數字電位計 IC 256 Step SPI 100kOhm RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| MCP41100E/SL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
| MCP41100E/SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Single/Dual Digital Potentiometer with SPI Interface |
| MCP41100-E/SN | 功能描述:數字電位計 IC 256 Step SPI 100kOhm RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。