參數資料
型號： MCP3204T-BI/SL
廠商： Microchip Technology
文件頁數： 9/40頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 2.7V 4CH SPI 14SOIC
標準包裝： 2,600
位數： 12
采樣率（每秒）： 100k
數據接口： 串行，SPI?
轉換器數目： 1
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 14-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 14-SOIC
包裝： 帶卷 (TR)
輸入數目和類型： 4 個單端，單極；2 個偽差分，單極
2008 Microchip Technology Inc.
DS21298E-page 17
MCP3204/3208
4.0
DEVICE OPERATION
The MCP3204/3208 A/D converters employ a
conventional SAR architecture. With this architecture,
a sample is acquired on an internal sample/hold
capacitor for 1.5 clock cycles starting on the fourth
rising edge of the serial clock after the start bit has been
received. Following this sample time, the device uses
the collected charge on the internal sample/hold
capacitor to produce a serial 12-bit digital output code.
Conversion rates of 100 ksps are possible on the
, “Maintaining Minimum Clock
Speed”, for information on minimum clock rates.
Communication with the device is accomplished using
a 4-wire SPI-compatible interface.
4.1
Analog Inputs
The MCP3204/3208 devices offer the choice of using
the analog input channels configured as single-ended
inputs or pseudo-differential pairs. The MCP3204 can
be configured to provide two pseudo-differential input
pairs or four single-ended inputs, while the MCP3208
can be configured to provide four pseudo-differential
input pairs or eight single-ended inputs. Configuration
is done as part of the serial command before each
conversion begins. When used in the pseudo-
differential mode, each channel pair (i.e., CH0 and
CH1, CH2 and CH3 etc.) is programmed to be the IN+
and IN- inputs as part of the command string transmit-
ted to the device. The IN+ input can range from IN- to
(VREF + IN-). The IN- input is limited to ±100 mV from
the VSS rail. The IN- input can be used to cancel small
signal common-mode noise which is present on both
the IN+ and IN- inputs.
When operating in the pseudo-differential mode, if the
voltage level of IN+ is equal to or less than IN-, the
resultant code will be 000h. If the voltage at IN+ is equal
to or greater than {[VREF + (IN-)] - 1 LSB}, then the
output code will be FFFh. If the voltage level at IN- is
more than 1 LSB below VSS, the voltage level at the
IN+ input will have to go below VSS to see the 000h
output code. Conversely, if IN- is more than 1 LSB
above VSS, then the FFFh code will not be seen unless
the IN+ input level goes above VREF level.
For the A/D converter to meet specification, the charge
holding capacitor (CSAMPLE) must be given enough
time to acquire a 12-bit accurate voltage level during
the 1.5 clock cycle sampling period. The analog input
model is shown in Figure 4-1.
This diagram illustrates that the source impedance (RS)
adds to the internal sampling switch (RSS) impedance,
directly effecting the time that is required to charge the
capacitor (CSAMPLE). Consequently, larger source
impedances increase the offset, gain and integral
linearity errors of the conversion (see Figure 4-2).
4.2
Reference Input
For each device in the family, the reference input
(VREF) determines the analog input voltage range. As
the reference input is reduced, the LSB size is reduced
accordingly. The theoretical digital output code pro-
duced by the A/D converter is a function of the analog
input signal and the reference input, as shown below.
EQUATION 4-1:
When using an external voltage reference device, the
system
designer
should
always
refer
to
the
manufacturer’s recommendations for circuit layout.
Any instability in the operation of the reference device
will have a direct effect on the operation of the A/D
converter.
Where:
VIN
=
analog input voltage
VREF
=
reference voltage
Digital Output Code
4096
V
IN
×
V
REF
---------------------------
=
相關PDF資料
PDF描述
17291-2SG-300 CONN RCPT 2POS PNL MNT SKT
AAA3MBZPKG CONN PLUG MALE 3PIN SILVER
AAA3FBZ CONN PLUG FEMALE 3PIN SILVER
MAX4410EUD+ IC AMP AUDIO .08W STER 14TSSOP
MAX9725CETC+T IC AMP AUDIO .025W STER 12TQFN
相關代理商/技術參數
參數描述
MCP3204T-CI/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 4-Channel/8-Channel 12-Bit A/D Converters with SPI⑩ Serial Interface
MCP3204T-CI/SL 功能描述:模數轉換器 - ADC 12-bit SPI 4 Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MCP3204T-CI/ST 功能描述:模數轉換器 - ADC 12-bit SPI 4 Chl RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MCP3208 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2.7V 4-Channel/8-Channel 12-Bit A/D Converters with SPI Serial Interface
MCP-320-81302-0B 制造商:Supermicro Computer Inc 功能描述:OPTIONAL FAN TRAY FOR ONE 40X28MM FAN IN SC813 - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*