- 您現(xiàn)在的位置：買賣IC網 > PDF目錄10482 > MCP3004T-I/ST (Microchip Technology)IC ADC 10BIT 2.7V 4CH SPI14TSSOP PDF資料下載
參數資料
| 型號： | MCP3004T-I/ST |
| 廠商： | Microchip Technology |
| 文件頁數： | 11/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 2.7V 4CH SPI14TSSOP |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 200k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 4 個單端，單極；2 個偽差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
2008 Microchip Technology Inc.
DS21295D-page 19
MCP3004/3008
5.0
SERIAL COMMUNICATION
Communication with the MCP3004/3008 devices is
accomplished using a standard SPI-compatible serial
interface. Initiating communication with either device is
done by bringing the CS line low (see Figure 5-1). If the
device was powered up with the CS pin low, it must be
brought high and back low to initiate communication.
The first clock received with CS low and DIN high will
constitute a start bit. The SGL/DIFF bit follows the start
bit and will determine if the conversion will be done
using single-ended or differential input mode. The next
three bits (D0, D1 and D2) are used to select the input
the configuration bits for the MCP3004 and MCP3008,
respectively. The device will begin to sample the
analog input on the fourth rising edge of the clock after
the start bit has been received. The sample period will
end on the falling edge of the fifth clock following the
start bit.
Once the D0 bit is input, one more clock is required to
complete the sample and hold period (DIN is a “don’t
care” for this clock). On the falling edge of the next
clock, the device will output a low null bit. The next 10
clocks will output the result of the conversion with MSB
first, as shown in Figure 5-1. Data is always output from
the device on the falling edge of the clock. If all 10 data
bits have been transmitted and the device continues to
receive clocks while the CS is held low, the device will
output the conversion result LSB first, as is shown in
Figure 5-2. If more clocks are provided to the device
while CS is still low (after the LSB first data has been
transmitted), the device will clock out zeros indefinitely.
If necessary, it is possible to bring CS low and clock in
leading zeros on the DIN line before the start bit. This is
often done when dealing with microcontroller-based
SPI ports that must send 8 bits at a time. Refer to
, “Using the MCP3004/
3008 with Microcontroller (MCU) SPI Ports”, for more
details on using the MCP3004/3008 devices with
hardware SPI ports.
TABLE 5-1:
CONFIGURE BITS FOR THE
MCP3004
TABLE 5-2:
CONFIGURE BITS FOR THE
MCP3008
Control Bit
Selections
Input
Configuration
Channel
Selection
Single/
Diff
D2* D1
D0
1
X
0
single-ended
CH0
1
X
0
1
single-ended
CH1
1
X
1
0
single-ended
CH2
1
X
1
single-ended
CH3
0
X
0
differential
CH0 = IN+
CH1 = IN-
0
X
0
1
differential
CH0 = IN-
CH1 = IN+
0
X
1
0
differential
CH2 = IN+
CH3 = IN-
0
X
1
differential
CH2 = IN-
CH3 = IN+
* D2 is “don’t care” for MCP3004
Control Bit
Selections
Input
Configuration
Channel
Selection
Single
/Diff
D2
D1 D0
1
0
single-ended
CH0
1
0
1
single-ended
CH1
1
0
1
0
single-ended
CH2
1
0
1
single-ended
CH3
1
0
single-ended
CH4
1
0
1
single-ended
CH5
1
0
single-ended
CH6
1
single-ended
CH7
0
differential
CH0 = IN+
CH1 = IN-
0
1
differential
CH0 = IN-
CH1 = IN+
0
1
0
differential
CH2 = IN+
CH3 = IN-
0
1
differential
CH2 = IN-
CH3 = IN+
0
1
0
differential
CH4 = IN+
CH5 = IN-
0
1
0
1
differential
CH4 = IN-
CH5 = IN+
0
1
0
differential
CH6 = IN+
CH7 = IN-
0
1
differential
CH6 = IN-
CH7 = IN+
相關PDF資料 |
PDF描述 |
|---|---|
| MS3100A20-18P | CONN RCPT 9POS WALL MNT W/PINS |
| V24B3V3M150BG | CONVERTER MOD DC/DC 3.3V 150W |
| UP050SL 270J-B-B | CAP CER 27PF 50V 5% AXIAL |
| MCP3004T-I/SL | IC ADC 10BIT 2.7V 4CH SPI 14SOIC |
| MS3106F-16-10S | CONN PLUG 3POS W/SOCKET SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP3008 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:MCP300X 10-Bit Analog-to-Digital Converters |
| MCP3008-I/P | 功能描述:模數轉換器 - ADC 10-bit SPI 8 Chl IND TEMP, PDIP16 RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3008-I/P | 制造商:Microchip Technology Inc 功能描述:A/D Converter (A-D) IC |
| MCP3008-I/SL | 功能描述:模數轉換器 - ADC 10-bit SPI 8 Chl IND TEMP, SOIC16 RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MCP3008-I/SL | 制造商:Microchip Technology Inc 功能描述:Analog/Digital Converter IC Number of Bi |
發(fā)布緊急采購，3分鐘左右您將得到回復。