參數資料
型號： MCP23017T-E/SS
廠商： Microchip Technology
文件頁數： 17/48頁
文件大?。?/td> 0K
描述： IC I/O EXPANDER I2C 16B 28SSOP
標準包裝： 2,100
接口： I²C
輸入/輸出數： 16
中斷輸出： 是
頻率 - 時鐘： 1.7MHz
電源電壓： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 28-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 28-SSOP
包裝： 帶卷 (TR)
配用： MCP23X17EV-ND - BOARD EVAL FOR MCP23X17
GPIODM-KPLCD-ND - BOARD DEMO LCD GPIO EXP KEYPAD
MCP23017/MCP23S17
DS21952B-page 24
2007 Microchip Technology Inc.
1.7
Interrupt Logic
If enabled, the MCP23X17 activates the INTn interrupt
output when one of the port pins changes state or when
a pin does not match the preconfigured default. Each
pin is individually configurable as follows:
Enable/disable interrupt via GPINTEN
Can interrupt on either pin change or change from
default as configured in DEFVAL
Both conditions are referred to as Interrupt-on-Change
(IOC).
The interrupt control module uses the following
registers/bits:
IOCON.MIRROR – controls if the two interrupt
pins mirror each other
GPINTEN – Interrupt enable register
INTCON – Controls the source for the IOC
DEFVAL – Contains the register default for IOC
operation
1.7.1
INTA AND INTB
There are two interrupt pins: INTA and INTB. By
default, INTA is associated with GPAn pins (PortA) and
INTB is associated with GPBn pins (PortB). Each port
has an independent signal which is cleared if its
associated GPIO or INTCAP register is read.
1.7.1.1
Mirroring the INT pins
Additionally, the INTn pins can be configured to mirror
each other so that any interrupt will cause both pins to
go active. This is controlled via IOCON.MIRROR.
If IOCON.MIRROR = 0, the internal signals are routed
independently to the INTA and INTB pads.
If IOCON.MIRROR = 1, the internal signals are OR’ed
together and routed to the INTn pads. In this case, the
interrupt will only be cleared if the associated GPIO or
INTCAP is read (see Table 1-7).
TABLE 1-7:
INTERRUPT OPERATION
(IOCON.MIRROR = 1)
1.7.2
IOC FROM PIN CHANGE
If enabled, the MCP23X17 will generate an interrupt if
a mismatch condition exists between the current port
value and the previous port value. Only IOC enabled
pins will be compared. Refer to Register 1-3 and
1.7.3
IOC FROM REGISTER DEFAULT
If enabled, the MCP23X17 will generate an interrupt if
a mismatch occurs between the DEFVAL register and
the port. Only IOC enabled pins will be compared.
1.7.4
INTERRUPT OPERATION
The INTn interrupt output can be configured as active-
low, active-high or open-drain via the IOCON register.
Only those pins that are configured as an input (IODIR
register) with Interrupt-On-Change (IOC) enabled
(IOINTEN register) can cause an interrupt. Pins
defined as an output have no effect on the interrupt
output pin.
Input change activity on a port input pin that is enabled
for IOC will generate an internal device interrupt and
the device will capture the value of the port and copy it
into INTCAP. The interrupt will remain active until the
INTCAP or GPIO register is read. Writing to these
registers will not affect the interrupt. The interrupt
condition will be cleared after the LSb of the data is
clocked out during a read command of GPIO or
INTCAP.
The first interrupt event will cause the port contents to
be copied into the INTCAP register. Subsequent
interrupt conditions on the port will not cause an
interrupt to occur as long as the interrupt is not cleared
by a read of INTCAP or GPIO.
Interrupt
Condition
Read Portn * Interupt Result
GPIOA
PortA
Clear
PortB
Unchanged
GPIOB
PortA
Unchanged
PortB
Clear
GPIOA and
GPIOB
PortA
Unchanged
PortB
Unchanged
Both PortA and
PortB
Clear
* Port n = GPIOn or INTCAPn
Note:
The value in INTCAP can be lost if GPIO is
read before INTCAP while another IOC is
pending. After reading GPIO, the interrupt
will clear and then set due to the pending
IOC, causing the INTCAP register to
update.
相關PDF資料
PDF描述
MCP23009T-E/MG IC I/O EXPANDER I2C 8B 16QFN
MCP23009T-E/SS IC I/O EXPANDER I2C 8B 20SSOP
MCP23017T-E/SO IC I/O EXPANDER I2C 16B 28SOIC
MCP23S08T-E/ML IC I/O EXPANDER SPI 8B 20QFN
MCP23S08T-E/SS IC I/O EXPANDER SPI 8B 20SSOP
相關代理商/技術參數
參數描述
MCP23018 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-Bit I/O Expander with Open-Drain Outputs
MCP23018-E/MJ 功能描述:接口-I/O擴展器 16B I/O Expander I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MCP23018-E/MJ 制造商:Microchip Technology Inc 功能描述:; Bus Frequency:3.4MHz; IC Interface Typ 制造商:Microchip Technology Inc 功能描述:IC, I/O EXPANDER, 16BIT, 3.4MHZ, QFN-24
MCP23018-E/SO 功能描述:接口-I/O擴展器 16B I/O Expander I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
MCP23018-E/SP 功能描述:接口-I/O擴展器 16B I/O Expander I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*