- 您現在的位置：買賣IC網 > PDF目錄3771 > MCP23017T-E/SS (Microchip Technology)IC I/O EXPANDER I2C 16B 28SSOP PDF資料下載
參數資料
| 型號： | MCP23017T-E/SS |
| 廠商： | Microchip Technology |
| 文件頁數： | 10/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 28SSOP |
| 標準包裝： | 2,100 |
| 接口： | I²C |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 1.7MHz |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
| 配用： | MCP23X17EV-ND - BOARD EVAL FOR MCP23X17 GPIODM-KPLCD-ND - BOARD DEMO LCD GPIO EXP KEYPAD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
MCP23017/MCP23S17
DS21952B-page 18
2007 Microchip Technology Inc.
REGISTER 1-6:
IOCON – I/O EXPANDER CONFIGURATION REGISTER (ADDR 0x05)
R/W-0
U-0
BANK
MIRROR
SEQOP
DISSLW
HAEN
ODR
INTPOL
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7
BANK: Controls how the registers are addressed
1 = The registers associated with each port are separated into different banks
0 = The registers are in the same bank (addresses are sequential)
bit 6
MIRROR: INT Pins Mirror bit
1 = The INT pins are internally connected
0 = The INT pins are not connected. INTA is associated with PortA and INTB is associated with PortB
bit 5
SEQOP: Sequential Operation mode bit.
1 = Sequential operation disabled, address pointer does not increment.
0 = Sequential operation enabled, address pointer increments.
bit 4
DISSLW: Slew Rate control bit for SDA output.
1 = Slew rate disabled.
0 = Slew rate enabled.
bit 3
HAEN: Hardware Address Enable bit (MCP23S17 only).
Address pins are always enabled on MCP23017.
1 = Enables the MCP23S17 address pins.
0 = Disables the MCP23S17 address pins.
bit 2
ODR: This bit configures the INT pin as an open-drain output.
1 = Open-drain output (overrides the INTPOL bit).
0 = Active driver output (INTPOL bit sets the polarity).
bit 1
INTPOL: This bit sets the polarity of the INT output pin.
1 = Active-high.
0 = Active-low.
bit 0
Unimplemented: Read as ‘0’.
相關PDF資料 |
PDF描述 |
|---|---|
| MCP23009T-E/MG | IC I/O EXPANDER I2C 8B 16QFN |
| MCP23009T-E/SS | IC I/O EXPANDER I2C 8B 20SSOP |
| MCP23017T-E/SO | IC I/O EXPANDER I2C 16B 28SOIC |
| MCP23S08T-E/ML | IC I/O EXPANDER SPI 8B 20QFN |
| MCP23S08T-E/SS | IC I/O EXPANDER SPI 8B 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCP23018 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-Bit I/O Expander with Open-Drain Outputs |
| MCP23018-E/MJ | 功能描述:接口-I/O擴展器 16B I/O Expander I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23018-E/MJ | 制造商:Microchip Technology Inc 功能描述:; Bus Frequency:3.4MHz; IC Interface Typ 制造商:Microchip Technology Inc 功能描述:IC, I/O EXPANDER, 16BIT, 3.4MHZ, QFN-24 |
| MCP23018-E/SO | 功能描述:接口-I/O擴展器 16B I/O Expander I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| MCP23018-E/SP | 功能描述:接口-I/O擴展器 16B I/O Expander I2C interface RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。