- 您現在的位置：買賣IC網 > PDF目錄69031 > MC9SDJ64MPVR2 (MOTOROLA INC) 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 PDF資料下載
參數資料
| 型號： | MC9SDJ64MPVR2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 |
| 封裝： | LQFP-112 |
| 文件頁數： | 43/102頁 |
| 文件大?。?/td> | 1007K |
| 代理商： | MC9SDJ64MPVR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MC9S12DJ64 Device User Guide — V01.02
45
would need to be set before any attempt to write to an external location. If there are no writable resources
in the external system, PE2 can be left as a general purpose I/O pin.
The Port E bit 3 pin can be reconfigured as the LSTRB bus control signal by writing “1” to the LSTRE bit
in PEAR. The default condition of this pin is a general purpose input because the LSTRB function is not
needed in all expanded wide applications.
The Port E bit 4 pin is initially configured as ECLK output with stretch. The E clock output function
depends upon the settings of the NECLK bit in the PEAR register, the IVIS bit in the MODE register and
the ESTR bit in the EBICTL register. The E clock is available for use in external select decode logic or as
a constant speed clock for use in the external application system.
4.2.1.3 Normal Expanded Narrow Mode
This mode is used for lower cost production systems that use 8-bit wide external EPROMs or RAMs. Such
systems take extra bus cycles to access 16-bit locations but this may be preferred over the extra cost of
additional external memory devices.
Ports A and B are configured as a 16-bit address bus and Port A is multiplexed with data. Internal visibility
is not available in this mode because the internal cycles would need to be split into two 8-bit cycles.
Since the PEAR register can only be written one time in this mode, use care to set all bits to the desired
states during the single allowed write.
The PE3/LSTRB pin is always a general purpose I/O pin in normal expanded narrow mode. Although it
is possible to write the LSTRE bit in PEAR to “1” in this mode, the state of LSTRE is overridden and Port
E bit 3 cannot be reconfigured as the LSTRB output.
It is possible to enable the pipe status signals on Port E bits 6 and 5 by setting the PIPOE bit in PEAR, but
it would be unusual to do so in this mode. LSTRB would also be needed to fully understand system
activity. Development systems where pipe status signals are monitored would typically use special
expanded wide mode or occasionally special expanded narrow mode.
The PE4/ECLK pin is initially configured as ECLK output with stretch. The E clock output function
depends upon the settings of the NECLK bit in the PEAR register, the IVIS bit in the MODE register and
the ESTR bit in the EBICTL register. In normal expanded narrow mode, the E clock is available for use
in external select decode logic or as a constant speed clock for use in the external application system.
The PE2/R/W pin is initially configured as a general purpose input with a pull-up but this pin can be
reconfigured as the R/W bus control signal by writing “1” to the RDWE bit in PEAR. If the expanded
narrow system includes external devices that can be written such as RAM, the RDWE bit would need to
be set before any attempt to write to an external location. If there are no writable resources in the external
system, PE2 can be left as a general purpose I/O pin.
4.2.1.4 Internal Visibility
Internal visibility is available when the MCU is operating in expanded wide modes or emulation narrow
mode. It is not available in single-chip, peripheral or normal expanded narrow modes. Internal visibility is
enabled by setting the IVIS bit in the MODE register.
相關PDF資料 |
PDF描述 |
|---|---|
| MC9SD64VPVR2 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 |
| MC9SDJ64VPVR2 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 |
| MC9SD64MPVR2 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 |
| MC9SD64VFUR2 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP80 |
| MC9SD64CPVR2 | 16-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP112 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC9SDT128BMPVR2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Freescale Semiconductor 功能描述: |
| MC9SDT256BCPVR2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC9SXDP512VPVR2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Freescale Semiconductor 功能描述: |
| MC9Z-2DB | 制造商:IDEC CORPORATION 功能描述:MC2D Color Scrn 2-split top/bt |
| MC9Z-3DB | 制造商:IDEC CORPORATION 功能描述:Super Bright Led Or Incandescent Lamp Illumination Rectangular- And Square-Body Control Units |
發布緊急采購，3分鐘左右您將得到回復。