參數資料
型號: MC9S08QB8CGK
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, BCC24
封裝: 5 X 5 MM, 1 MM HEIGHT, 0.65 MM PITCH, ROHS COMPLIANT, MO-220VHHC-1, QFN-24
文件頁數: 35/36頁
文件大?。?/td> 1331K
代理商: MC9S08QB8CGK
MC9S08QB8 Series MCU Data Sheet, Rev. 3
Electrical Characteristics
Freescale Semiconductor
8
3.4
Thermal Characteristics
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and voltage regulator circuits, and it is user-determined rather than being controlled by the
MCU design. To take PI/O into account in power calculations, determine the difference between actual pin
voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high
pin current (heavy loads), the difference between pin voltage and VSS or VDD will be very small.
The average chip-junction temperature (TJ) in °C can be obtained from:
TJ = TA + (PD × θJA)
Eqn. 1
where:
Table 3. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to 3.8
V
Maximum current into VDD
IDD
120
mA
Digital input voltage
VIn
–0.3 to VDD +0.3
V
Instantaneous maximum current
Single pin limit (applies to all port pins)1, 2, 3
1
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp
voltages, then use the larger of the two resistance values.
2 All functional non-supply pins, except for PTA5 are internally clamped to V
SS and VDD.
3 Power supply must maintain regulation within operating V
DD range during instantaneous and
operating maximum current conditions. If positive injection current (VIn > VDD) is greater than
IDD, the injection current may flow out of VDD and could result in external power supply going
out of regulation. Ensure external VDD load will shunt current greater than maximum injection
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
ID
±25
mA
Storage temperature range
Tstg
–55 to 150
°C
Table 4. Thermal Characteristics
Rating
Symbol
Value
Unit
Operating temperature range (packaged)
TA
TL to TH
–40 to 85
°C
Maximum junction temperature
TJM
95
°C
Thermal resistance 28-pin SOIC
θ
JA
70
°C/W
Thermal resistance 24-pin QFN
92
°C/W
Thermal resistance 16-pin TSSOP
129
°C/W
相關PDF資料
PDF描述
MC9S08QE32CLD 8-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, PQFP44
MC9S08QE32CFT 8-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, QCC48
MC9S08QE32CLC 8-BIT, FLASH, 50.33 MHz, MICROCONTROLLER, PQFP32
MC9S08QE4CPG 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP16
MC9S08QE4CWJ 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO20
相關代理商/技術參數
參數描述
MC9S08QB8CGK 制造商:Freescale Semiconductor 功能描述:IC 8BIT MCU HCS08 20MHZ QFN-24
MC9S08QB8CTG 功能描述:8位微控制器 -MCU S08 8K FLASH QB8 TSSOP16 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QB8CTGR 功能描述:8位微控制器 -MCU S08 8K FLASH QB8 TSSOP16 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QB8CWL 功能描述:8位微控制器 -MCU S08 8K FLASH QB8 SOIC28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC9S08QB8CWL 制造商:Freescale Semiconductor 功能描述:IC 8BIT MCU HCS08 20MHZ WSOIC-28