參數資料
型號： MC92600
廠商： Motorola, Inc.
英文描述： High-speed, Full-duplex, Serial Data Interface(高速全雙工串行數據接口)
中文描述： 高速，全雙工，串行數據接口（高速全雙工串行數據接口）
文件頁數： 41/82頁
文件大?。?/td> 1056K
代理商： MC92600
Chapter 4. System Considerations
4-3
Repeater Mode
4.3.1 10-Bit Interface Mode
When the device is in TBI mode (TBIE = high) the internal 8B/10B encoder and decoder
are bypassed and the 10-bit data received is forwarded directly to the transmitter. Running
disparity is assumed correct and is not checked. This is important when using
disparity-based word synchronization where incorrect running disparity is used as a word
synchronization event marker. 10-bit mode must be enabled for disparity-based word
alignment to operate properly because it allows the improper disparity to pass through the
repeater.
When byte interface mode is enabled (TBIE = low), received data is passed through the
8B/10B decoder where it is converted into its eight-bit data or control byte. Running
disparity and code validity are checked and reported with the received byte at the receiver
interface as described in Section 3.5.4, òReceiver Interface Modes.ó The decoded byte is
re-coded by the transmitters 8B/10B encoder for transmission.
NOTE:
Byte interface mode must not be used with non-aligned mode
or disparity-based word synchronization.
4.3.2 Byte Alignment Mode
The byte alignment mode must be consistent with the transmitter and receiver with which
the repeater is being used. All byte alignment modes are supported in repeater mode.
When establishing byte alignment for the link through the repeater, the byte alignment
sequence must be repeated twice, once for the repeater and once for the destinations
receiver. For example, if the byte aligned with realignment mode is enabled
(BSYNC_0/BSYNC_1 = low/low), at least eight idle characters must be transmitted, four
for repeater alignment and four for the destinations receiver alignment.
4.3.3 Word Synchronization Mode
Word synchronization may be used in repeater mode. This allows the incoming bytes to be
synchronized into their corresponding words, removing cable skew from the transmission
Half-Speed Enable
HSE
Dont care
User programable depending on desired reference
clock frequency. See Section 4.3.6 for mode
details.
Double Data Rate
DDRE
Dont care
User programable depending on desired reference
clock frequency. See Section 4.3.6 for mode
details.
Table 4-2. Settings for Repeater Mode (Continued)
Mode
Signals
Recommended
State
Description
相關PDF資料
PDF描述
MC9S12DB128B MC9S12DT128B
MC9S12DB128BCFU MC9S12DT128B
MC9S12DB128BCPV MC9S12DT128B
MC9S12DB128BMFU MC9S12DT128B
MC9S12DB128BMPV MC9S12DT128B
相關代理商/技術參數
參數描述
MC92600JUB 功能描述:IC SERDES QUAD 1.25GBAUD 217PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 串行器，解串行器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 功能:解串器 數據速率:2.5Gbps 輸入類型:串行 輸出類型:并聯 輸入數:- 輸出數:24 電源電壓:1.8 V ~ 3.3 V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:64-TQFP 裸露焊盤 供應商設備封裝:64-TQFP-EP（10x10） 包裝:管件
MC92600VMB 制造商:Freescale Semiconductor 功能描述:
MC92603VF 功能描述:IC TXRX ETH QUAD GIG 256-MAPBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件
MC92603VM 功能描述:IC ETH TXRX QUAD GIG 256-MAPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
MC92604VM 功能描述:IC ETH TXRX DUAL GIG 196-MAPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*