參數資料
型號： MC8610PX800GZ
廠商： FREESCALE SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： MICROPROCESSOR, PBGA783
封裝： 29 X 29 MM, PLASTIC, FCBGA-783
文件頁數： 76/96頁
文件大?。?/td> 1237K
代理商： MC8610PX800GZ
MPC8610 Integrated Host Processor Hardware Specifications, Rev. 2
Hardware Design Considerations
Freescale Semiconductor
78
SerDes—Receiver lanes configured for PCI Express are allowed to be disconnected (as would occur when a PCI
Express slot is connected but not populated). Directions for terminating the SerDes signals is discussed in Section 3.10,
3.6
Pull-Up and Pull-Down Resistor Requirements
The MPC8610 requires weak pull-up resistors (2–10 k
Ω is recommended) on open drain type pins including I2C pins and PIC
interrupt pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 53.
Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most
have asynchronous behavior and spurious assertion will give unpredictable results.
Refer to the PCI 2.2 specification for all pull-ups required for PCI.
The following pins must not be pulled down during power-on reset: DIU_LD[5:6], MSRCID[1:2], HRESET_REQ, and
TRIG_OUT/READY.
The following are factory test pins and require strong pull up resistors (100
Ω – 1 kΩ) to OVDD: LSSD_MODE,
TEST_MODE[0:3].
The following pins require weak pull-up resistors (2–10 k
Ω) to their specific power supplies: LCS[0:4], LCS[5]/DMA_DREQ2,
LCS[6]/DMA_DACK[2], LCS[7]/DMA_DDONE[2], IRQ_OUT, IIC1_SDA, IIC1_SCL, IIC2_SDA, IIC2_SCL, and
CKSTP_OUT.
The following pins should be pulled to ground with a 100-
Ω resistor: SD1_IMP_CAL_TX, SD2_IMP_CAL_TX. The following
pins should be pulled to ground with a 200-
Ω resistor: SD1_IMP_CAL_RX, SD2_IMP_CAL_RX.
When the platform frequency is 400 MHz, cfg_platform_freq must be pulled down at reset. Also, cfg_dram_type[0 or 1] must
be valid at power-up even before HRESET assertion.
For other pin pull-up or pull-down recommendations of signals, see Section 1, “Pin Assignments and Reset States.”
3.7
Output Buffer DC Impedance
The MPC8610 drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push-pull
single-ended driver type (open drain for I
2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the
value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 51). The output impedance is the average of two
components, the resistances of the pull-up and pull-down devices. When data is held high, SW1 is closed (SW2 is open) and
相關PDF資料
PDF描述
MC8610VT800GZ MICROPROCESSOR, PBGA783
MC8640DVU1000HE 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA1023
MC8640DTHX1250HC 32-BIT, 1250 MHz, MICROPROCESSOR, CBGA1023
MC8640TVU1000HC 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA1023
MC8640VU1250HC 32-BIT, 1250 MHz, MICROPROCESSOR, CBGA1023
相關代理商/技術參數
參數描述
MC8610PX800J 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610TPX1066JB 功能描述:微處理器 - MPU REV 1.1 8610 1.0V -40C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MC8610TPX1066JZ 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:MPC8610 Integrated Host Processor Hardware Specifications
MC8610TPX1067G 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8610TPX1067J 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*