- 您現在的位置：買賣IC網 > PDF目錄25639 > MC80C52CXXX-12SB (TEMIC SEMICONDUCTORS) 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | MC80C52CXXX-12SB |
| 廠商： | TEMIC SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CDIP40 |
| 文件頁數： | 47/80頁 |
| 文件大?。?/td> | 5152K |
| 代理商： | MC80C52CXXX-12SB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
247
XMEGA A [MANUAL]
8077I–AVR–11/2012
Bit 1:0 – DREINTLVL[1:0]: Data Register Empty Interrupt Level
These bits enable the data register empty interrupt and select the interrupt level, as described in “Interrupts and
Programmable Multilevel Interrupt Controller” on page 125. The enabled interrupt will be triggered when the DREIF flag
in the STATUS register is set.
21.15.4 CTRLB – Control register B
Bit 7:5 – Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always write these bits to zero
when this register is written.
Bit 4 – RXEN: Receiver Enable
Setting this bit enables the USART receiver. The receiver will override normal port operation for the RxD pin, when
enabled. Disabling the receiver will flush the receive buffer, invalidating the FERR, BUFOVF, and PERR flags.
Bit 3 – TXEN: Transmitter Enable
Setting this bit enables the USART transmitter. The transmitter will override normal port operation for the TxD pin, when
enabled. Disabling the transmitter (writing TXEN to zero) will not become effective until ongoing and pending
transmissions are completed; i.e., when the transmit shift register and transmit buffer register do not contain data to be
transmitted. When disabled, the transmitter will no longer override the TxD port.
Bit 2 – CLK2X: Double Transmission Speed
Setting this bit will reduce the divisor of the baud rate divider from16 to 8, effectively doubling the transfer rate for
asynchronous communication modes. For synchronous operation, this bit has no effect and should always be written to
zero. This bit must be zero when the USART communication mode is configured to IRCOM.
This bit is unused in master SPI mode operation.
Bit 1 – MPCM: Multiprocessor Communication Mode
This bit enables the multiprocessor communication mode. When the MPCM bit is written to one, the USART receiver
ignores all the incoming frames that do not contain address information. The transmitter is unaffected by the MPCM
setting. For more detailed information, see “Multiprocessor Communication Mode” on page 244.
This bit is unused in master SPI mode operation.
Bit 0 – TXB8: Transmit Bit 8
TXB8 is the ninth data bit in the character to be transmitted when operating with serial frames with nine data bits. When
used, this bit must be written before writing the low bits to DATA.
This bit is unused in master SPI mode operation.
Bit
765
43210
+0x04
–
RXEN
TXEN
CLK2X
MPCM
TXB8
Read/Write
R
R/W
Initial Value
0
相關PDF資料 |
PDF描述 |
|---|---|
| MQ80C32-25SCD | 8-BIT, 25 MHz, MICROCONTROLLER, CQFP44 |
| MQ80C32E-20SHXXX:D | 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44 |
| MD80C52CXXX-16SCD | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40 |
| MF180C51-16R | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44 |
| MQ80C32E-20SHXXX:D | 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC80D21000G | 制造商:COR 功能描述:RN |
| MC80F0104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0104B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0104D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
| MC80F0204 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。